Rating of the best axes

Axes are represented by a wide assortment on the modern market, but each type is used to perform specific tasks. In order not to make a mistake when buying, it is worth knowing the rating of the best manufacturers of this tool.

Any ax is used to work with wood. It can be a small-sized model for hunting or tourism, a tool for giving or doing carpentry work.

Classically shaped products are used for cutting across the grain of wood, as well as for felling trees. Such a device can be made with a single or double cutting edge. For splitting, another tool is used, in which the head has the shape of a pointed wedge.

Splitters are used to harvest firewood, since they allow you to split large logs in which a conventional ax gets stuck.

The group of standard axes includes:

• carpenter's ax;
• cleaver;
• carpenter's ax.

The working surface of such a tool is usually limited by a bit (blade) at one end and a butt at the other, although some designs have two bits opposite each other or a pickaxe on one side.

The top corner of the bit, where the cutting edge starts, is called the toe, and the bottom is called the heel. Either side on the sides is the cheek, which is sometimes complemented by ears. The part of the blade that goes down below the rest is called the beard. Although it is an outdated shape, it is sometimes still used because it has an elongated edge that is twice the size of the rest of the blade.

A carpenter's ax is used to work with wood chips. Its thin blade, sharpened at an angle of 30-35 degrees, easily penetrates wood bars, but only if they are not very thick. It is larger than the carpentry and weighs about 1.5 kg. Particular attention is paid to its sharpening, as it must be very sharp in order to be able to sand without difficulty.

A carpenter's tool is usually operated with only one hand, so its weight reaches 700 g. It is a small but convenient design. In its shape, the tool is very similar to a carpenter's one, only its sharpening angle varies from 18 to 20 degrees. The blade may have a thin section, and the butt should not be massive.

In a separate group there are massive cleavers, which are distinguished by their high weight and handle length. It is the handle that allows you to make the maximum swing and hit the log with maximum force. Such a tool is used exclusively for chopping wood. Its weight can reach 4 kg.

The following tools can be included in the specialized tool category:

• tourist;
• for felling timber;
• for chopping meat;
• for hunting;
• fireman.

A touring ax is always a small, lightweight toolDesigned to be used in one hand when camping or traveling. The design may include a hammer. If the models are with a hammer, then they allow you to use the ax as two useful tools. Such a product is usually sold in a compact size with a protective case.

A tourist ax weighs up to 500 g, sometimes there is a free cavity in the handle for storing small items. At the end of the handle there is a hole through which a string is threaded so that you can hang the tool in a convenient place or even on a belt.

The meat ax has a unique blade shape. The fact is that when working with this material, the tool gets stuck in the bone, quickly becomes blunt, so sharpening plays an important role. Such axes are made with the shape of forging under a razor, the blade is sharpened under the lens. Thus, the blunt base quickly breaks bone, and the razor shape makes it easy to penetrate the flesh. The weight of the structure is about 3.5 kg.

Fire ax - specialized tool, which has special requirements specified in the standards. This product comes on sale with a quality certificate and has a short service life - only 18 months, since it can withstand a huge load and at the same time must remain strong and reliable.

Fire axes can be with a pickaxe on the other side of the blade or with a sledgehammer. The first feature allows a firefighter to quickly break the lock or stay on the roof, and the second - to break down a dense wall.

A hunting ax is used for butchering meat carcassestherefore it is small in size. The weight of the structure is no more than 700 g, and its length reaches 400 mm. As a rule, these are all-metal products with a rubberized grip on the handle, which simplifies the process of working with the tool.

The felling tool has a major difference - The edge is thin, but with a wide, thick blade. This design helps to penetrate the wood across. The best option when the product has a flat, elongated blade with rounded edges. This shape makes it easy to penetrate wood fibers.

Among all the axes on the market, a list of the best models from different manufacturers should be highlighted.

• Stihl 1926 universal ax weighing 700 g and 400 mm long. The blade is made of specialized high quality steel. The production process uses a hand-forged method. Supplied with a waxed ash handle. The main area of ​​use is delimbing and splitting small chips. Sold with extra blade protection in the form of a leather sheath.

• Hultafors Carpenter's Ax 840304. This model is made in Sweden and is characterized by the use of special steel in the construction. The cutting edge has an even shape, the working surface is forged by hand several times, thereby increasing the density, and, accordingly, the service life of the ax. There is a small notch near the handle for easy operation. The ax is impregnated with linseed oil. The weight of the structure is 800 g and its length is 500 mm.

• Solid Forged Gross 21500. The model is made entirely of steel. It has not only reliability and durability, but also an acceptable cost. The total length of the structure is 36 cm. There is a rubberized grip on the handle, which provides the proper level of comfort when using the tool.

• Ganzo GSA-01YE. This is a tourist hatchet with light weight and dimensions. In the design, the manufacturer used steel grade 3CR13. The width of the blade is 44 mm, the length of the handle is 347 mm. The weight of the ax is 975 g. The model is completed with a plastic cover that is put on the cutting edge.

• Carpenter's "Bars 21410". The model weighs only 600 g. The handle is made of two-component rubberized fiberglass. Cutting part hardness - HRc 48-52. The product can be praised for its unique durability and resistance to aggressive environments. The handle is capable of absorbing vibrations that occur during operation.

• "Siberian Bulat Ermak". Such a tool is made in Russia and forged by hand using a special technology that uses three layers of metal. The hardest part is the core. The weight of the structure is only 1 kg, the handle length is 38 cm.

• Cleaver Ochsenkopf OX 635 H BIG OX. This model is equipped with additional grip reinforcement. The forged blade has a pivoting nose, which increases the impact surface. The blade is protected, the handle is made of thick wood. It is made of hazel.

• American Cleaver by Geolia weighing 1 kg is equipped with a fiberglass hatchet. The working blade is well ground and coated with bitumen, which protects against negative environmental influences. The light weight allows the tool to be used with one hand, delivering a powerful blow and splitting the wood in two halves.

Several types of steel are used for the production of axes, but the 9XC brand is considered the best. Before making a tool from it, the steel is subjected to high-temperature treatment twice, which reduces the level of deformation during broaching.

During the forging process, the workpiece is stretched and the cross-section is reduced. - this is how the necessary plasticity and strength appears in the metal. In simpler terms, the ax becomes capable of withstanding a blow against a tree, while maintaining its integrity.

The 9XC grade contains 0.9% carbon, chromium - 1.5% and the same amount of silicon. Carbon is responsible for strength, chromium adds hardness to the alloy. The latter also protects against corrosion. Silicon is responsible for rust resistance.

When choosing a handmade ax, it is worth knowing that the lack of the necessary experience from the master will lead to the fragility of steel. For a lumberjack and for splitting firewood, the tool will need to be selected differently. Despite the fact that in both cases you have to work with wood, the design of the tool will be different.

The carpenter's ax has a very thin profile. A thin blade has the ability to easily penetrate the material with minimal effort from the user, but it cannot cope with thick logs - the material will simply get stuck.

The buyer's choice should always be based primarily on the nature of the work being done. If the tool is purchased for tourism or hunting, then it should be small. The mini-ax fits easily into a backpack or can be hung on a belt in a protective case.

You can buy quality goods in a professional sports store, while paying special attention to the quality of steel and other characteristics.

For a common general ax, the stats can be summarized as follows:

• sharp blade;
• thin bit;
• conical head;
• average weight - up to 3 kg;
• the handle should be made of medium-length wood (38 cm);
• flexibility.

The cleaver has a wide profile of the metal part, which makes it difficult to use it as a cutting tool. It is so wide that it cannot chop small pieces of wood - only large logs. On the other hand, its blade is ideal for splitting wood because it will not cut the fibers, but will simply split them in half.

The main characteristics of this tool are:

• heavy base;
• the metal part is made in the form of a wedge;
• the handle is long and straight;
• requires an experienced user to operate.

The pocket-sized hatchet is the smallest, however, quite sturdy option and can be used for splitting small chips.This is the perfect variation for a hike as it won't take up a lot of space or add weight to your carry. To perform household tasks, it is worth choosing a larger tool, the handle of which should reach 40 cm. If a cleaver is purchased, then its length should be much larger.

As for weight, when buying, you need to understand who will use the tool and for what purposes. If this is a teenager or a woman, then it is desirable that the structure weighs as little as possible, respectively, the product should not be with a wooden or all-metal handle, but made of fiberglass.

It should be understood that the handle, which is made of wood:

• strong;
• heavy;
• absorbs shock well;
• breaks down quickly;
• it can be easily replaced in the event of a breakdown.

Reinforced plastic in comparison with this material is very light and durable, but when exposed to a chemical it can be damaged.

As you can easily see, each ax model is suitable for one specific purpose. Below are other tool characteristics that a purchaser should consider when choosing a good option.

• The size. You need to take the tool by the blade and turn the handle up - it should fit under the armpit. Thus, experts determine the ideal dimensions.
• Ax blade should be perfectly aligned. To be convinced of this, you need to take the metal part in your hand and look.
• Balance check by placing the blade between the index and thumb. He should stand level and not roll over to one side.