How to eliminate condensation on cold water pipes?

Rust that occurs on cold water pipes causes a lot of trouble for the owners of houses and apartments. The reason for this phenomenon in many cases is water droplets formed on the surface of the pipes.

Condensation is quite common. It mainly forms on cold water pipes. The reasons for this are the presence of high humidity in the room air and the difference between the air temperature and the temperature of the pipeline.

This phenomenon occurs just like dew on grass leaves in the morning. Under certain conditions (air humidity, temperature and atmospheric pressure), the so-called "dew point" is formed, upon reaching which the water vapor present in the air settles on the surface of the surrounding objects.

Steam also settles on the surface of water pipes, which seem to "sweat", becoming covered with drops. For this effect to appear, the surface temperature must be lower than the ambient temperature. Therefore, this happens with cold water pipes in the bathroom and toilet, which are cooled due to the passage of a cold stream through them with a temperature below the temperature of the air in the room.

If water does not flow through the pipe, then the pipe, together with the water in it, heats up to ambient temperature. Condensation is not possible under these conditions.

Therefore, when water droplets are detected on the pipe, it is necessary to accurately find out the location of the source of water movement. This can be a toilet cistern, through which water flows imperceptibly due to lost or torn gaskets. This movement of water through the pipe is quite enough to cool it and form condensation. Also, a poor-quality gasket on one of the taps, through which the water flow passes, may turn out to be a source.

In addition, the reason for the formation of water droplets can also be found in neighbors who live higher on any of the floors, if, for example, their cistern is leaking. In this case, condensation can form on the risers with water passing through the apartments from bottom to top. In this case, the constant movement of water and, accordingly, the cooling of the pipe occurs due to these leaks. When determining such a reason and a desire to eliminate it, it is necessary to inform the tenants who are located above.

Rust is one of the consequences of condensation. The formation of rusty streaks not only spoils the appearance of metal parts, but also destroys them. Often, condensation also occurs on risers that pass vertically through the apartment. In this case, the paintwork may peel off.

The droplets fall on the floor, forming small puddles, which cause the floor covering to collapse. Moisture can also deteriorate the furniture in the room.Also, due to the constant accumulation of moisture on surfaces, mold and mildew can occur, which have a negative impact on human health. The appearance of mold in hard-to-reach places of plumbing units is especially unpleasant.

If you notice the moisture formed on the pipes, you should immediately take measures to eliminate it. First of all, it is necessary to wipe off the formed condensate and dry the place of its appearance.

It is important not to allow moisture to build up. To do this, you should establish the reason for its appearance. In this case, it is necessary to find out which source gives a constant flow of water, as a result of which the surface of the pipes is cooled. To determine this, you need to check the toilet cistern and all taps for a constant leak. You should also pay attention to the washing machine installed in the house, through which water can flow if there are valve malfunctions.

You can check the performance of the ventilation system with a simple sheet of paper. When you bring it to the opening of the operating ventilation, you can notice a slight movement of the sheet. This is an indication that the ventilation is working. But to determine the effectiveness of the installed ventilation, you need to invite specialists.

If it is found that condensation forms on the riser, it is necessary to involve the neighbors on top, who may have a leak in the plumbing equipment, to identify the cause. In this case, condensation will also be observed on their pipes.

If the identified problem was not too serious, then it can be successfully solved by replacing the gasket on the drain tank or faucet. However, the solution is not always that simple.

In some cases, the cause is improper pipe routing, in which the hot and cold pipes pass close to each other. This is sufficient for condensation to form. Indeed, if there is a flow of water through both pipes, one of them heats up, and the other cools. From such a temperature drop, moisture is formed. Often such situations arise in private homes, where piping is carried out without the involvement of specialists.

In such cases, the use of a special thermal insulation material that can be wrapped around the water supply can help. This way you can insulate, eliminate mutual heat transfer, and protect the pipes. This method is quite effective and does not require capital work on the alteration of the water supply.

If the reason lies in insufficient exhaust from the room, then a fan must be installed at the ventilation outlet to create a forced air flow. This removes excess moisture from the room.

Plumbing professionals have extensive experience in finding the cause of condensation and eliminating it effectively. For example, one of the modern ways to solve the problem is to coat pipes with a special liquid heat-insulating compound.It is applied to the surface of the pipes, forming a durable, elastic and non-corrosive layer when it dries to get rid of moisture build-up.

However, with a very large temperature difference, the pipes must be additionally insulated. For this, polyethylene foam is often used, which is fixed with ordinary wire. It is lightweight and not subject to decay. It is produced both in the form of sheets and in the form of soft tubes of various diameters with a longitudinal cut.

For maximum effect, it is necessary that the inner diameter of the pipe matches the outer diameter of the water pipe. In this case, the tube is put on tightly, without unnecessary gaps. If it is of a smaller diameter, then there will be a gap, if it is larger, it will dangle. At the same time, it will practically not bring any benefit. Ease of use lies in the fact that you can put the part on the pipes yourself, immediately getting the desired result.

Before using them, it is necessary to clean the pipe, remove rust and degrease the surface with a solvent or acetone. After that, putty is applied, and on top - a layer of fabric, without waiting for the putty to dry. Layers of fabric are wound overlapping each other, without gaps, and at the end they are fixed with a bandage or strong thread. This method is quite simple and effective.

When building a private house in order to prevent such phenomena, one should take into account the existing sources of heat and high humidity, as well as their mutual placement. Based on this, it is worthwhile to immediately do enhanced ventilation of the premises.

For information on how to eliminate condensation on cold water pipes, see the next video.