How to properly cut the grass with a trimmer?

In the midst of the summer season, people who have their own plots have a problem. It lies in the fact that after winter and spring, grass and other vegetation grows very quickly in these areas. Today we will consider options for mowing grass. For example, it is better to disassemble ordinary trimmers, since they provide a person with more scope for action due to direct movement with this technique, and they are relatively inexpensive.

The general rules of use should definitely be reminded to those who are first thinking about how to remove grass with a trimmer and do not yet know how to use it. It is these foundations that will help you start cleaning your site with high quality.

Among summer residents, a tendency to use trimmers is increasingly emerging, because unlike lawnmowers, they allow you to clear grass in hard-to-reach places, and professional models can even help you handle tree branches. Another plus of the trimmer is the ability to work at height and cut branches, which can also greatly help in cleaning on your territory.

Another important point is security. Since brushcutters have a high rotation speed (they reach several thousand revolutions per minute), even a small stone can fly out at high speed and cause harm to a working person.

All trimmer parts check and review before starting work. Make sure the trimmer works. Since they are electric and gasoline, you will need to organize their work depending on the type of equipment. Electric should be plugged into the power supply and charged if it is not charged, and gasoline should be refueled if required.

Let the trimmer run in for the first time. If you bought a new device, then you need to let it run for a few minutes without load in order for the motor, knives, fishing lines, and rotating elements to start. This can be called a kind of warm-up for equipment, and besides, it can help prevent some troubles before direct work, because the assembly and quality of garden equipment are different.

Running in an electric trnimmer involves several stages.

1. To get started, start and work with the trimmer for a short time, literally 5 minutes.
2. You can then increase the run time up to 10 minutes, but you need to monitor the motor so that it does not overheat.
3. After a few trials of the electric trimmer, you can use it on a permanent basis. Do not forget about the engine cooling system, which is available as an additional function on some models.

If you do not know which type of mowing is best to start with, then it is better to try cutting a low lawn with a line. This will allow the engine to come into operation smoothly. There is no need to immediately load it with a large amount of work.

The quality of your work also depends on what technique you use.For proper technique, you must be able to hold the unit, and for convenience, put it on correctly. This is because not all trimmers have a shoulder strap. If you have one, then you need to put it on so that you feel comfortable. There are device models whose strap may be uncomfortable, so try to put on the trimmer as comfortably as possible.

Another function is to adjust this belt. On higher quality models, its convenience was given a special role and special positions were made that will allow the scythe driver to feel comfortable. You can adjust the belt in height, choosing the one you need.

Now let's talk about how to properly hold the unit. Different types of trimmers have different handles. For some, it is made in the form of a bicycle handlebar (which ensures the distribution of the load on both hands). On some units, you can see the handle in the shape of the letter D. The bike version needs to be held firmly with both hands.

Despite the presence of rubberized handles, it is best to rely on yourself and not hope that they will not slip. Hold the D-shaped grip with one hand and palm to provide a wider grip. This will give you full control of the stick, which will have a positive impact on handling.

In order to mow the lawn efficiently and quickly, you need to follow the technique and know some features that will save you time and effort. You can work faster, now we'll tell you how.

Divide your site into zones. This will help you understand how much you need to accomplish. Also, you will have no delusions about whether you have already worked here and whether you are not going through the second time. For the first time in the seasons, the lawn is mowed at a level of 4-5 cm, gradually decreasing to 3-4. Set the mowing rate yourself. You can leave more, less. It all depends only on you.

If the motor is located underneath, the likelihood of moisture ingress will be even higher. It is also not recommended to work with the trimmer in the rain all for the same reasons. Water ingress can cause a short circuit, which in the future may develop into a malfunction of the unit. That's why it is better to wait for more favorable weather for work.

It is recommended to work clockwise. It is this direction that will leave the grass cut by you on the outside of the entire mowed area. Hold the coil at least 5 centimeters during operation. This is a safe mowing option that will work well for those new to this type of tool. When it comes to working near a fence or other places where you only need to mow a small part, use the edge of the line. This will ensure that the engine does not overload and wear out.

Use a disc as a cutting element because meadow vegetation is tougher than usual. It is better than fishing line specifically for hay in that it cuts through dry grass better. This way, the grass will not get stuck on the line, which could result in poor engine performance. The hay does not need to be cut small, it should be quite tall, so try to cut the hay at the root.

To create a level lawn surface, try to process the greenery with garden equipment as low as possible.... So all the grass will be the same height, which will make the coating even and beautiful. Don't forget about the tilt. For best results, tilt the device at least 30 degrees towards the grass surface. This will cut the grass as low as possible. Any other irregularities can be removed with garden shears, if any.

This requires special attention. Tall grass needs more careful processing than simple grass. The fact is that there is an effect of winding the vegetation onto a coil. In this case, the grass remains on it and does not allow the mechanism to rotate at full power. This significantly slows down the process and reduces the number of revolutions.

To prevent this from happening walk the path in several stages. Gradually cut a certain amount down the height, going down and down the stem.

It is also necessary to take into account the fact that if your technique is new, then mowing tall grass can be even more difficult... Therefore, do not work for a long time, so as not to overload the motor. It will be enough 15-20 minutes with a break of 15 minutes. Since it is better to mow the grass in several stages, do not forget about the grass catcher. It will start to clog very quickly and this will lead to problems with the instrument. Clean completely so that it does not take too long before the next cleaning.

Before using the technique, it will be advisable for you to read the instructions from the manufacturer itself and familiarize yourself with the general functions and structure of the trimmer. The functions should be located on the control stick. Understanding the constituent parts and components is helpful in the sense that you will know how you can and should handle it. Selecting the load for the motor, work for the cutting elements - all this will be useful to you during operation.

Pay attention to the following points.

• First of all, this is technique. She has malfunctions and breakdowns. Before work, carefully check all the components of your technique, because mowing the lawn with such tools is an important matter. You need to check the filters (clean if necessary), the fuel level, cutting elements (in case of a malfunction, it is better to take the knives to the master), the engine and other parts. This can be done after work, but some manufacturers recommend before it.
• Some trimmers have a motor cooling and vibration damping system, but they are not present everywhere. Therefore, watch out for the heating of the motor during operation, because its overheating can lead to problems. Occasionally draw your attention to bolts and other items. Although the extinguishing system can work, but on some representatives of garden assistants, the places of the paper clips are still gradually unwound, in the end it will lead to a breakdown.
• Sometimes it also happens that the turnover falls. In this case, first check all filters and then try to work. It is much better to test the technique before the immediate action.
• If parts are broken, it is better to contact a technical center. Do not try to repair the equipment yourself, because this can only accelerate the breakdown. Mechanics have a complete understanding of this technique, you better trust them.

How to work with the trimmer correctly, see below.