How to connect a TV cable to each other using an extension cord and other methods?
A break or violation of the integrity of a television cable is often the result of careless actions during any rearrangements or repairs in the house. The second possible cause is aging and wear of the cable. Repairing or replacing the cable is not difficult. Sometimes it is necessary to remove the damaged part of the cable, and then build it up to the required length. Let's consider in more detail the ways to build up a television cable.
When building is necessary
The TV cable needs to be extended in the following cases:
- if it is accidentally damaged in some section of its length, and when this section was removed, the remaining length was not enough;
- when rearranging furniture, the TV took a different place, as a result of which the cable length was insufficient;
- relocating the antenna to another location also required an external extension of the television wire.
In the latter case, you may also need additional antenna amplifierto compensate for losses in a much longer cable.
Varieties of antenna extenders and connection rules
Antenna extension cords are produced ready-made - cable with already existing F-connectors and plugs or connectors of the "tulip" type.
The cable length is several meters. It makes no sense to use a long length (more than 10 m) - the antenna needs an additional broadband amplifier designed for the “decimeter” range.
For an indoor antenna, where signal attenuation is provided by the walls of the house itself, a building, a structure, 5 m of cable is enough.
Until 2020, analog television, which also used the "meter" frequency range, needed a composite antenna amplifier designed for the 49-860 MHz frequency band. With the advent of digital TV, the range in which television of an all-digital format operates has been "compressed" from 480 to 600 MHz. At the same time, in one 8 MHz frequency band, designed for one analog channel, a whole multiplex of digital television broadcasts - from 8 to 10 TV channels of standard definition or 1-3 HD-channels.
The development of "digital" allows you to watch TV channels practically without on-air noise, and if the signal level is insufficient, the image will simply slow down. To avoid this, extension cords and antenna amplifiers.
The most common ways to lengthen a cable are - use F-connectors or splitters. The first ones allow you to build up the cable, almost without violating the integrity of the cable structure: the braid, which serves as a shield from external interference, and the central conductor. The latter make the antenna collective, serving as concentrators (splitters). Splitters can contain an additional amplifier stage - the so-called active splitter, but more often passive connecting devices are used.
To connect a break in the cable with an F-connector, do the following:
- Peel off the protective sheathing of the braid by 2.5 cm.
- Unwrap the braid (it consists of thin wires) and take it back.
- Remove the protective sheath of the center conductor at a distance of 1 cm. Be careful - the core should not have any notches (often copper-plated steel or aluminum alloy) that can lead to rupture.
- Disassemble the connector by unscrewing the retaining nut, slide the nut onto the cable.
- Press the center conductor with the conductor into the plug-in transition from one side.The end of the center conductor will come out from the back of the adapter (no more than 5 mm needed).
- Tighten the nut. It will press the braiding and prevent the cable from easily pulling out of the adapter.
- Strip and press the other end in the same way at the cable break.
The center conductors in the adapter will touch each other, and the braids will be connected through the housing. If the cable is completely replaced with a longer one, the connection to the TV is performed directly: instead of the traditional tulip-type connector, the TV receiver itself already has a built-in F-connector.
To connect cables from several TVs through a splitter, you should perform the following operations:
- press the ends of the cables into the plugs according to the above diagram;
- connect the antenna (with an amplifier) to the splitter input, and TVs to its outputs.
Place the splitter in a convenient location. Check that there is a TV signal on all TVs, for which switch to different channels (if there are several) on each connected TV. If there is a TV amplifier on the antenna or in the splitter, then you need to check that it is turned on (power is supplied to it).
Other ways to extend the cable
Correctly connecting a television cable is a simple matter, it seems. The main thing here is to connect the central cores and braids separately, after which the electrical contact will be provided. But any connection without connectors and splitters - interference with the integrity of the braid. Even a small gap will be a gap for the passage of interference from the outside and loss (re-emission) of the signal from the center conductor.
Due to the laws of physics and due to the ability of an electrical signal with a frequency of more than 148 kHz to be reflected back into the surrounding space without amplification and re-transmission, RF cables must be reliably shielded. The fact is that A coaxial cable is a kind of waveguide: full reflection from the braid back to the central conductor prevents it from being significantly lost. The only limiting factor here is the characteristic impedance, which ensures signal attenuation over a long cable line.
Twisting without additional shielding of the cable is considered the most unreliable of the homemade ones.
It is necessary to strip the cable as in the case of the F-connector connection. Twisting the central conductors, insulate them with electrical tape from the braid. Then they connect the braids themselves in the spliced place, also protecting them with a layer of electrical tape.
Soldered cable Is a much more efficient way. Do the following:
- Strip the cable according to the instructions above.
- Cover the center conductor and braid with a thin layer of solder. For a copper conductor, rosin is sufficient as a tinning improver. Copper-plated aluminum, common steel and stainless steel require a soldering flux that contains zinc chloride.
- Solder the center conductor and insulate the connection with tape or tape from other conductors. One of the best is fabric (non-combustible) electrical tape - it does not melt from overheating and does not support combustion.
- Wrap the braid solder area (over the electrical tape) with aluminum or copper foil. It is also possible to wind a stripped and pre-tinned enamel wire over the insulating layer. The wrapping place should not contain gaps.
- Connect the braids and solder them. The best result will be obtained by soldering them to an artificially recreated protective layer. Act quickly - do not overheat the junction, as the plastic insulation may melt and the center conductor may be exposed. As a result, the cable line can become short-circuited, which will require reworking the connection from the very beginning. Fast soldering (less than a second) is achieved using a soldering flux: the solder instantly envelops the surfaces to be joined, which cannot be said about rosin.
Make sure there is no short circuit - "ring" the cable line for a "break" using a multimeter (tester included in the resistance measurement mode).Resistance should be conditionally endless. If so, then the cable is restored, the line is ready for operation.
It is possible to extend the TV cable by using detachable and conventional plugs - one at the same time enters the other. Do the following:
- strip the ends of the desired length of cable;
- solder a regular plug to one end and a detachable plug to the other.
These connectors are an improved version of cable connections that came from the Soviet era. Instead of "petals", the connector uses a solid connecting ring-shield, which does not interfere when the plug is connected to the connector.
Such connections are used for AV connections to this day - for example, in CCTV cameras.
Correctly determining the length of the cable and calculating the possible signal loss during forced splice, you can restore the operation of the cable line. A damaged or repaired cable is not used to connect radio repeaters. But for television and radio reception, it will do.
A visual overview of the connection of the television cable to each other is presented in the following video.
The comment was sent successfully.