Sharp TV repair

Sharp technology is generally reliable and sound. However, the repair of TVs of this brand still has to be carried out. And here there are a number of subtleties that must be taken into account.

Consider troubleshooting Sharp television receivers pertinently on the example of models LC80PRO10R, LC70PRO10R and LC60PRO10R. The same approach is recommended for other products of the same brand. The instructions say that if it is impossible to enable a three-dimensional image, you need to check if this option is disabled in the settings. But the main thing is not even in a specific technical configuration.

You need to start diagnosing any TV with cleaning it from all contaminants. Cleaning is carried out inside and outside, and with the utmost care. External examination sometimes reveals malfunctions, especially of a purely mechanical nature. But the overwhelming majority of them are found only with in-depth research. For this purpose, resistance is measured and other technical parameters are set using special equipment.

If it is not possible to find a specific cause immediately, it is necessary to sequentially examine:

• power unit;
• control board;
• contact tracks;
• screen LEDs;
• the area through which the signal passes from the radiation receiver of the console to the central processor.

Complaints are common enough that the light is on with red light, but the TV does not want to turn on. Professional repairmen say: "does not leave the standby mode." A similar situation can be provoked by various factors, but it is necessary to start solving the problem with the most probable of them. First of all check the operation of the remote control and its batteries. Sometimes it is enough to replace them without calling the masters if the remote control does not respond.

It should be borne in mind that a lit indicator does not mean that the power supply is fully operational. They check it by evaluating the voltage in standby mode and how it changes when you try to turn on the TV. It is also necessary to measure the level of filtration.

Sometimes, after fixing a problem with the power supply, they find that the problem has not gone away, and the TV still does not turn on. This usually means the loss of information recorded in the memory chips. In this case you will have to refresh the software using a special device (programmer)... This technique is mainly used by professionals in workshops. It is almost impossible to use them without special training.

Periodically, the TV does not turn on because the power circuits of the main electronic board are broken. They use several secondary sources of current supply, as well as DC-DC, current-converting or voltage stabilizing devices. Without such conversion and stabilization, it is almost impossible to ensure normal use of the processor and other parts of the TV.

The indicator flashes (color changes from red to green and back) when if the processor sends a command to all the main blocks, but the response is not very good. Problems can arise, for example, in the power supply or in the inverter.If the processor does not receive a confirmation of the complete order, then the inclusion is canceled, and the TV is again put into standby mode. Sharp LCD receivers, after 5 problematic startup attempts, block starting until the errors are cleared through the service menu. Or until the information in the Eeprom memory is replaced.

In this case, it is imperative to eliminate another specific cause of the failure:

• problem lamps;
• disturbances in the operation of the inverter;
• failures in the power supply;
• defects in other components of the TV chassis.

Chaotic blinking occurs almost as often as correct color changes. This can be provoked by a variety of problems. Researching the entire TV is almost never complete. Examine the power supply unit, secondary converters, data exchange buses. Next, they study how the launch commands are given and how these commands are processed on the periphery of the television chassis.

Sometimes there are complaints that the Sharp TV has sound but no picture. The very first assumption that needs to be checked is whether the cable supplying the screen, as well as the cable transmitting video information, has come off. The next step is to test the functionality of the cables themselves.

But if these methods do not help, we can assume the worst - failure:

• the screen itself;
• internal cables;
• electronic boards and systems responsible for signal processing;
• irregularities in the operation of the inverter supplying current to the backlight lamps.

Do-it-yourself Sharp TV repair is quite possible. But not always. If the device does not start, you need to check if the vertical scan is in order. Failures in it appear:

• lack of a picture;
• blurry image;
• unauthorized shutdown of the TV.

It is unlikely that you will be able to cope with the breakdown of the scanner on your own.... It is unlikely that you will be able to cope with your own hands and with the loss of sound. Unless only if the reason is related to settings or malfunctions on the TV transmitter. But if the main electronic components are damaged, you will have to contact professionals. Poor reception quality is often associated with:

• damage to the antenna;
• her poor connection;
• incorrect installation of the antenna;
• insufficient sensitivity of the receiving device.

Accordingly, you will have to either change the antenna (cable), or rearrange, reconnect them. You can also change the power supply unit with your own hands. The most basic knowledge of electrical engineering is sufficient for this.

For information on how to repair a Sharp TV, see the following video.