Arlight LED strips

LED strips are an important decorative part of building facades, public places or private houses. These products are most often used for illumination, and also allow you to draw people's attention to certain objects. One of the manufacturers of LED strips is Arlight.

Arlight LED strips are represented by a wide assortment, where each customer can find different models depending on voltage, size, scope, color range and much more. Some tapes are equipped with special remotes so that it is possible to provide lighting control depending, for example, on the time of day or the type of event, which is very useful when installing lighting in public places.

Arlight has specific sets of products, which are several models of different types. As a rule, these assemblies are intended for a narrow specialization and are not as widely demanded as single copies.

Sealed models are presented in several levels of filling assurance:

• with silicone on top of the board;
• Fully filled in transparent silicone / matt tube;
• using additional sealant.

This variety allows the consumer to choose LED strips that must meet a specific design, which may be caused by the peculiarities of the conditions where the lighting will be installed.

Arlight models are available in a wide range of colors. Among the products are single color, RGB adjustable, as well as Microled, Normaled, variable color temperature and many others. At the same time, the products of this manufacturer are not limited to ribbons alone. There are also various accessories for connection in the form of loops, terminals and connectors with connectors.

An important feature can be called a different price range, which starts from inexpensive models and ends with the most diverse "smart" and universal tapes.

A sealed model, which is widely used due to its simplicity. Standard size 3528, LED density - 120 pcs. / meter, radiation angle - 120 degrees. Color temperature in the range from 5700 K to 6500 K, color rendering index - more than 85. Ingress protection class IP67, luminous flux is 820 lumens / meter, power - from 8.4 to 9.6 V / meter, minimum cut - 25 mm. The total length is 5 m, the width is 11 mm, and the height is 5 mm.

The tape has a flexible Lux-structure, the inner part is trimmed with red tape. This model can be called one of the most demanded due to its characteristics and price. It should be added that RTW 2-5000PGS 12V is presented in a large number of other colors, among which there are cheap options due to the lower demand from the buyer.

Model with standard size 5060, class of dust and moisture protection IP 20, color temperature from 5800K to 6500K. The radiation angle is 120 degrees, the density of LEDs is 60 pcs. / meter, luminous flux and power, respectively, are 10.8 V at the minimum and 12 V at the maximum. The minimum length is 100 mm, the width is 10 mm, and the height is 2.4 mm.

The voltage drop can vary from 18 to 21 V, the standard tape length is 5 meters. The structure is in a Lux-profile, which has a flexible structure, which allows the tape to be installed on various surfaces in a variety of shapes.

An expensive LED strip that has some installation features. The standard size of the LED is 5630, the ingress protection class is IP20, the radiation angle is 120 degrees. It is worth noting the high color temperature in the range from 7700 K to 9600 K, which distinguishes this model from many others. Density of LEDs - 60 pcs. / meter, luminous flux - 2900 lumens. The minimum power per meter is 25.2 V, the maximum is 30 V.

The standard length is 5 meters, the width is 12 mm, and the height is 1.5 mm. It is important to pay attention to the fact that this LED strip is installed exclusively on the profile of the corresponding power due to the high characteristics of the model. Warranty - 5 years, operating temperature range - from -30 to +45 degrees.

Double side-lit strip featuring a high density of 240 LEDs. / meter, class of dust and moisture protection IP 20, daylight, color temperature from 4800 K to 5300 K. The luminous flux per meter is 1920 lumens, the maximum power reaches 96 V. Current consumption from 3.6 to 4 amperes depending on the type of work.

Another advantage is the short section length of 25 mm, which makes it possible to install the lighting on small objects. The length of one set is 5 meters, the width is 15 mm, the height is 2 mm, a 3-year warranty.

One of the widest LED strips from this manufacturer. Color temperature in the range from 5800 K to 6500 K, radiation angle - 120 degrees. Density of LEDs - 420 pieces per meter, standard size 2835, ingress protection class IP20. Luminous flux - 3800 lumens, power - 30 V. The minimum length can be 50 mm. Warranty for 5 years, operating temperature range - from -30 to +45.

Flexible stabilized tape with Lux profile, LED density - 60 pcs. / meter, class of dust and moisture protection IP20, radiation angle is 120 degrees. Size 2835, minimum color temperature 4800 K, maximum color temperature 5200 K. Luminous flux - 410-440 lumens / meter, power - from 4.2 to 4.6 V. The minimum length is 166.7 mm, width - 10 mm, height - 1.6 mm.

A distinctive feature of this model is a large overall length of 30 meters, which is most often used when providing large-scale lighting. Warranty for 5 years, current consumption - 0.19 A for 1 meter of tape, standard operating temperature range.

Despite the fact that the diode strip itself can be quite diverse, it is worth paying attention to some accessories that significantly affect the operation of lighting. You should start with profiles, the main function of which is to protect products from physical damage and moisture. The main material for the manufacture of these components is anodized aluminum alloy, which ensures a long service life.

Some types of profiles are designed for certain types of belts, for example, closed or open, as well as different heights, widths and other characteristics.

Simpler accessories are equipped with a built-in flange, surface-mounted or corner profile. Also, do not forget that there is a difference between where the installation will be carried out - to the ceiling or to the floor, because here, too, there are different options for components.

RGB strips usually have an option such as a dimmer. The element is a special control panel with which the user can change the lighting power, as well as adjust the color rendering.

Connecting Arlight LED strips is a simple two-step circuit.

• First, you need to detach the double-sided tape located on the back of the product. This installation variation allows the tape to be placed on any material, since the adhesive adheres to many surfaces, but only if they are smooth.
• The second step involves connecting the LED strip to a power source. It is necessary to connect the wires of the LEDs and the transformer, before that, be sure to disconnect the main power grid system, as provided for by the safety rules.

You only need to cut the tape in certain areas, which are marked with special lines. Do not forget about the operating criteria, as knowing them will allow you to use the product longer.