IE error on LG washing machine: causes and remedies

A washing machine should make life easier, but sometimes it becomes a source of unnecessary hassle. Automatic models from LG can periodically scare their owners with IE error. The code appears on the screen, and the washing machine simply stops working. In fact, this is not at all scary, the problem can be easily eliminated on your own.

LG washing machine throws IE error code at the most inopportune moment. Usually everything is ready to be washed, the laundry is loaded, and the compartments are filled with powder and conditioner. Such two letters on the screen signal that the equipment was not able to draw water in the time allotted for this process. It is worth noting that while the motor of the machine is running, a characteristic noise is heard. However, the water either does not enter the drum at all, or it pours out in a small stream. The error can also manifest itself in equipment without a display. In this case, the prewash and main wash lamps come on at the same time.

After starting the program, the washing machine has about 8 minutes to draw water into the tank for further operation. If, after a predetermined period, there is no liquid or there is not enough liquid, then the electronics sees the problem and stops working. Washing will resume after solving the problem.

The good news is that an IE bug doesn't always signal a broken washing machine. It usually notifies the owner that the water pressure is too weak. Common reasons for the error are as follows.

1. Utilities cut off the water supply... You should immediately check if there are any problems with the plumbing. Perhaps the area is undergoing renovation work, so the water supply is turned off.
2. The tap is turned off just in front of the hose of the washing machine. It is worth remembering that it is the lack of pressure that most often causes this error. Check all areas where water might be cut off on the way to the washing machine. If the taps were closed, then it is enough to open them, and the work of the equipment will resume.
3. The tap in front of the machine hose is not open enough... In this case, the equipment receives too little water pressure, which is simply not enough for full-fledged work. Always open the tap in front of the hose completely.
4. The water inlet hose is damaged or kinked... The connection of the equipment to the pipes should be checked. It happens that the hose is bent, in which case the washing machine simply cannot draw water. If the tube is damaged, then it must be replaced. With a new hose, the technician will again receive the required amount of water, and the error will go away.
5. Clogged filter... The mesh catches various debris, prevents it from getting into the washing machine tank. If it becomes clogged, then the liquid simply does not leak. The filter should be periodically checked and cleaned under running water. In some cases, additional cleaning agents must be used to remove dirt. Before removing the mesh, you must shut off the water supply.

In most cases, lack of water or low pressure is associated with easily fixable problems.

In some cases, the taps for shutting off the water break and open to the end.You just need to replace the structure so that the washing machine gets the right pressure.

Usually, the solution to the problem is to restart the water supply or increase the pressure. It happens that manipulations do not help. This means that the error is related to equipment failure. Sometimes you can do the repair yourself, but in some cases you will have to contact a specialist. Here are the types of breakdowns and a solution.

1. Usually the problem is due to a faulty filler valve. It is this part that guarantees the flow of liquid into the tank. Breakdown is manifested in the fact that water does not flow, because the valve simply does not open. In rare cases, the opening is too small, and not enough fluid enters. To solve the problem, the valve needs to be changed. It should be noted that in normal working condition the part is always in the closed position. The opening occurs only when it is necessary to get water.
2. The pressure switch may break. This part is a sensor that monitors the water level inside the tank. The pressure switch is electronic and generates a current of a certain frequency. With a filled tank, the indicator should reach 24.6 kHz. If the value is different, then the corresponding error appears. To correct the problem, you must first purge the tube. It happens that it just gets hammered. If the manipulation did not help, then the sensor must be replaced with a new one. To repair the washing machine, you will have to contact a specialist.
3. In rare cases, the electronic controller breaks down... This is a small microcircuit that controls the washing machine. With such a problem, you will have to contact the service center. Usually the part can be simply repaired. It is enough to re-solder the parts that have burned out. However, in some situations, the controller must be replaced.
4. The error can be caused by spontaneous leakage of water from the tank.... This can happen if the washing machine is not properly connected to the sewer. It turns out that the water comes off immediately after it enters. The program sees the error and displays it on the screen, stopping the work.
5. In some cases, the IE error appears on the screen as a result of a software glitch. To solve the problem, it is enough to turn off the power for 15 minutes. After restarting, the technician should start working as usual. Be sure to press the shutdown button before unplugging the power cord.

In most cases, the problem of lack of water is fairly easy to solve at home. However, the whole process takes time. It is much easier to avoid such situations. Here are some important guidelines for using LG washing machines.

1. Connect the washing machine to the sewer according to instructions... There you can avoid a lot of unpleasant situations associated with the supply and discharge of water.
2. The hose should be removed at least once a year.... The tube should be checked for integrity and cleaned of debris that may have accumulated on the walls.
3. It is also necessary to rinse the filter screens on both sides of the hose. It is better to remove them with pliers. You need to wash the filters under the strong pressure of running water. You can lightly tap the mesh with your fingers to release debris.
4. It is important to make every effort to stabilize the voltage in the mains. This reduces the likelihood of disabling the electronics. To solve the problem, you can use a special stabilizer for equipment.
5. The pressure switch tube should be cleaned once a year.... It is quite easy to remove and blow it off.
6. It is important to monitor the condition of the valves that are designed to shut off the water. It happens that they interfere with the washing machine from taking away liquid in the right volume.

You should not panic in such a situation. You should first check for water in the pipes, and then proceed to inspect the machine itself.

For the reasons for the IE error of the LG washing machine and how to fix it, see below.