Miele washing machine repair

Many housewives start to panic when a washing machine breaks down. However, the most frequent breakdowns can be eliminated independently without a specialist. It is not at all difficult to cope with simple problems. It is enough to know the weak points of the units of a certain brand and take proper care of it. Miele machines are distinguished by high-quality components and assembly, but they can sometimes fail.

The average user of washing machines is not always able to quickly and accurately determine the malfunction. However, there are signs by which you can find out which parts are not working correctly. It is not uncommon for Miele washing machines to break down due to power surges. With abrupt changes in the values ​​of this indicator, a short circuit may occur in the electronic module of the washing machine, the engine, wiring and so on may burn out.

Hard water also often causes breakdowns associated with the heating element. At the same time, strong scale can harm not only the heating element itself, but also the control module. To make it easier to determine the breakdown, the machine can issue special codes. For example, when water is not collected in the tank, then the display shows F10.

If there is a lot of foam, F16 will appear, and if the electronics are faulty, F39. When the hatch is not locked, F34 will be displayed, and if the unlock is not activated - F35. A list of all errors can be found in the instructions that come with the washing device.

Malfunctions can happen if the parts have simply served their time or, in other words, worn out. Also, breakdowns often occur when the rules for operating the washing unit are violated. Low-quality detergents can also lead to various problems.

In washing devices from Miele, most often breakdowns affect parts such as the drain filter, as well as the pipes for draining the liquid. The water level sensor or pressure switch also often fails. Malfunctions can affect the drive belt, the electronics module, the door lock, various sensors and electrical circuit elements. In a device with a vertical type of loading, the drum can jam.

There are few typical problems with German cars, and they are easy to fix on your own. To repair your Miele washing machine, you only need to have a range of tools and a little knowledge of the device at hand. Of course, compliance with safety precautions is also a prerequisite.

You can understand that the drain pump is not working by the water that remains after the end of the washing program. In most cases, simply cleaning the drain filter is sufficient. As a rule, in most models of washing machines, this part should be found in the lower part on the right or left side. If cleaning did not help, then you need to look for the cause in the pump and the pipe.

It is advisable to remove these parts, for which the front cover is unscrewed on a typewriter. Before removing, it is important to unscrew the clamps connecting to the tank and disconnect the wiring terminals. The fastener bolts are also removed.

The pressure switch allows you to control the water level in the tank. If it breaks down, an error about "empty tank" or "water overflow" may appear on the display. It is impossible to repair this part, only replace it. To do this, it is necessary to remove the top cover from the device, under which the required sensor is located at the side panel. Be sure to disconnect the hose and all the wiring from it.

In place of the inoperative sensor, a new one must be installed. Then all the necessary elements must be connected to the pressure switch in the correct sequence.

It is not easy to detect this malfunction, since most often the mode is performed in full, but only with cold water. You can notice this problem by the poor quality of the wash, which cannot be corrected with another mode or new detergent. You can also touch the sunroof glass during the period of active washing at high temperature conditions. If it is cold, then the water is clearly not heating up.

The reasons for this malfunction may lie in a broken heating element, thermostat or electronics. If the heating element is out of order, then it will have to be replaced with a new one. On average, a heating element lasts no more than 5 years. It is better to change this part with the help of a specialist.

The thermostat can give a false signal, and as a result, the water will not heat up. In this case, replacing the temperature sensor will also help.

Sometimes washing starts as usual, but you can see, looking through the hatch, that the drum remains motionless. This happens due to a breakdown of the drive belt, engine, software malfunction. Also, the drum can stop when a foreign object gets between it and the tank.

To better understand what happened, you should disconnect the washing unit from the mains and try to rotate the drum with your hands.

In case of strong knocks and vibrations, check whether the unit is installed correctly, the bearings and shock absorbers are in good condition, and the uniform distribution of things inside the drum. Often this breakdown occurs due to the fact that the bearings have simply served their due date. It can be fixed by installing new bearings.

Shock absorbers allow you to damp the vibrations of the drum during rotation. If at least one shock absorber fails, the operation of the washing unit is immediately disrupted. In addition to knocking and unpleasant sounds, this can be determined by the displaced drum. To replace the shock absorbers, you must purchase a new repair kit, preferably from the manufacturer of the machine.

Before tackling the shock absorbers, you will need to remove the drum, control unit and disconnect all wiring. And only after that you can get to the necessary parts. After replacement, everything will have to be installed in the reverse order. Therefore, it is best to photograph all connections in advance when parsing.

If the spin mode is incorrect, the problem may be in the engine, or rather in the malfunction of the brushes. This problem can be easily solved by replacing with new brushes. However, it is worth using the help of qualified specialists who understand the engines.

Leakage of water under the washing device can be caused by wear of the gasket on the inlet hose, rupture of the cuff of the hatch or pipe. All these parts are inexpensive, and everyone can definitely put on the cuff.

Lack of water means that the wash cannot start. After checking the tap and water supply, pay attention to the supply hose, inlet filter and water supply program.In this case, it is usually sufficient to disassemble the water supply system, clean each of its elements, and then reinstall it. If after starting the machine does not work, then you will have to change the parts for new ones.

The device does not respond when you press the button, which is responsible for turning on when the power supply is burnt out, the power supply is broken, or the outlet is flashed. Of the listed reasons, you can only eliminate the replacement of the socket on your own, but it is better to leave the rest to the masters. Sometimes the washing unit does not turn on due to a poorly closed hatch.

Experts recommend contacting a service center if a Miele washing machine breaks down. This is especially necessary if the device is still under warranty. Of course, simple repairs or replacement of old parts with new ones can be handled even without experience. However, if the malfunction is quite serious, then it is better to immediately contact the master.

How to repair Miele washing machines, see below.