What to do if water leaks from the LG washing machine?

Water leakage from the washing machine is one of the most common problems, including when using LG appliances. The leak can be both barely noticeable and cause a flood. In any of these cases, the damage must be repaired immediately. This can be done in two ways: by inviting a master or by yourself.

Before you start repairing your LG washing machine, you need to disconnect it from the power. This will create a safe environment for working with the device. First of all, it is important to notice at what stage of operation the machine began to leak. Observations will help to facilitate diagnosis and quickly cope with the problem.

After a breakdown has been noticed, you need to inspect the device from all sides, even tilt it to inspect the bottom. It is difficult for one to do this, someone may need help.

Basically, LG washing appliances can leak due to several factors:

• violation of the rules for using the device;
• factory defect, which was allowed during the manufacture of units and other components of the machine;
• failure of any element of the working system;
• washing with low-quality powders and conditioners;
• leakage of the drain pipe;
• crack in the tank of the device.

Let's consider several options for resolving the problem.

1. If during the survey it was found that water flows from the tank, the device will need to be repaired. Most likely, the cause is a broken hose, and it will need to be replaced.
2. If it turns out that water is leaking from under the door of the device, most likely, the cuff of the hatch has been damaged.
3. The leak does not always occur due to a breakdown - it could be the fault of the user. If you notice a leak after a few minutes of washing, you need to check how tightly the door of the filter and the device itself is closed, as well as whether the hose is well inserted. This tip is most relevant if you have recently cleaned your clipper dust filter. Sometimes, after cleaning it, an inexperienced user does not fix this part tightly.
4. If the user is convinced that he has closed the lid tightly, then carefully inspect the place where the drain hose and pump are connected. If the intersection is loose, a sealant will help solve the problem (be sure to take a waterproof one), but it will be safer to simply replace the parts.
5. Although water collects under the clipper, the cause of the problem is sometimes higher. It is necessary to carefully inspect the dispenser (compartment) intended for powders and conditioners. It is located more often in the left corner of the car. Sometimes the dispenser is too dirty, which is why there is an overflow of water during spinning and typing. It is necessary to inspect both inside and outside, pay special attention to the corners - more often the leak appears in these places.

If the user doubts that the leak is due to the powder receptacle (located in front), the tray must be completely filled with water, wipe the bottom of the compartment with a cloth until dry and then observe the process. If the water starts to flow out slowly, this is exactly the reason. Unfortunately, this part sometimes breaks even in new models of LG typewriters after 1-2 years of using the device. This problem stems from the unscrupulousness of the assemblers who wanted to save on parts.

If the user noticed that water flows precisely during washing, the reason is precisely the breakdown of the pipe. For an accurate diagnosis, you need to remove the top wall of the device.

Sometimes the problem arises from a leak in the drain pipe, which is directed towards the pump from the tank of the device. In order to check this, you need to tilt the machine and look at the insides of the case from below. It is likely that the cause of the breakdown lies precisely in the pipe. To inspect it, you will need to remove the front panel of the machine and examine the area where the connection is.

If the leak is caused by a crack in the tank, this is one of the most unpleasant problems. Most often, it is impossible to eliminate it on your own; you will need to replace the tank, which is expensive. This crack could occur with frequent washing of shoes, as well as when sharp objects get into the machine: nails, iron inserts from a bra, buttons, paper clips.

A crack could also appear due to a defect that the manufacturer allowed, but in any case, the device will have to be disassembled in order to remove the tank and inspect it carefully. To perform such manipulations, it is better to call the master, so as not to make things worse.

If during inspection of the unit it is found that water is leaking from under the door, the seal lip may be damaged. In this case, the problem can be easily solved - a special patch or waterproof glue will help to fix the problem. And also the cuff can be simply changed to a new one, it is inexpensive.

The article discussed the most common causes of failure of the LG washing machine, as well as ways to eliminate them. Better anyway if possible, contact the master or the service center if the machine is under warranty... To avoid problems in principle, you should be more careful with the device and check things before loading them into the tank.

Find out what to do if water is leaking from your LG washing machine below.