Indesit washing machine belt: why it flies and how to put it on?

Over time, the period of use of any household appliances expires, in some cases even earlier than the warranty period. As a result, it becomes unusable and is sent to a service center. Washing machines are no exception. But still there are certain malfunctions that can be eliminated with your own hands, in particular, replacing the drive belt of the washing unit. Let's figure out why the belt for the Indesit washing machine flies and how to put it on correctly.

If you do not take into account the electronic component of the washing machine, which allows you to control various washing modes, then the internal structure of the unit seems to be relatively easy to understand.

This is done in the following way - a pulley (wheel) is installed on the rear side of the drum. The friction mechanism, which is a steel wheel, with a groove or flange (rim) in a circle is driven by the friction force generated by the belt tension.

The wheel of the same interaction, only with a smaller diameter, is also installed on the electric motor. Both pulleys are connected by a drive belt, the key purpose of which is to transfer torque from the washing machine's electric motor to the drum. The torque of the electric motor from 5,000 to 10,000 rpm is prohibitive. To reduce - reduce the number of revolutions, a light pulley of large diameter is used, rigidly fixed on the drum axis. By changing the rotation from a small diameter to a large one, the number of revolutions is reduced to 1000-1200 per minute.

Rapid actuation of the belt occurs due to operational irregularities. Either the structure of the washing machine directly or indirectly influences this component. Let's analyze the possible factors more thoroughly.

• The narrow body of an Indesit washing machine may well affect the pulley, increasing the wear rate. This happens due to the fact that the drum is ground close to the electric motor. During operation (especially during spinning), the wheel begins to create strong vibration, in contact with the belt. From friction on the body or drum, the part wears out.
• If the machine is constantly operated under loads for which it is not designed, the belt will one day fly off. If this happens for the first time, just pull the element into place, and the washing machine will continue to work.
• If, at high drum speeds, the belt does not jump off for the first time, it is likely that it has stretched out. There is only one way out of the situation - to change it to another.
• The belt can fly off not only due to its own fault, but also due to a weakly fixed electric motor. The latter will begin to change its position from time to time and loosen the belt. To eliminate the malfunction - fix the electric motor more securely.
• Loose wheel attachment is similarly a factor in belt slipping off. All that is needed is to securely fix the pulley.
• There may be deformations of the wheel or axle (often the belt itself, jumping off, bends them). In such a situation, you will need to purchase a new spare part.
• The shaft is mated to the body of the washing unit by means of a cross. This means that if the crosspiece fails, the belt will fly off. The way out is the purchase and installation of a new part.
• Depleted bearings can cause the drum to rotate skewed, which will first of all lead to a weakening of the belt, and after a while to its collapse.
• The belt often breaks on a typewriter that is rarely used. During long breaks, the rubber simply dries up, losing its characteristics. When the machine is started to be used, the element is rapidly abraded, stretched and torn.

To put on a drive belt that simply fell off, or install a new one instead of a torn one, a simple sequence of operations should be performed. The step-by-step actions for carrying out the work will be as follows.

1. Disconnect the machine from the electrical outlet.
2. Close the valve regulating the water intake into the tank.
3. Remove the remaining liquid, for this take a container of the required volume, unscrew the intake hose from the unit, drain the water from it into the prepared container.
4. Dismantle the back wall of the washing machine by unscrewing the fastening screws located along its contour.
5. Inspect the drive belt, wiring and sensors around it for any damage.

When the source of the machine breakdown is established, proceed to eliminate it. If the belt is intact and just fell off, reinstall it. If it is torn, put in a new one. The belt is installed as follows: put the belt on the pulley of the electric motor, then on the drum wheel.

After the defective element has been replaced, you need to reinstall the back wall of the machine body. Then it is connected to communications and to the electrical network. You can do a test wash.

One of the most frequent factors for belt slipping off is an increased load; therefore, in order to increase the service life of the product, experts recommend keeping the weight of the laundry loaded into the drum under control and trying not to exceed the maximum load of the washing machine.

And yet - as a rule, under normal use, the drive belt of a washing machine can withstand 4-5 years of use... Therefore, the recommendation is that it is advisable to buy this important element in advance, so as not to carry out emergency work later.

How to change the belt on the Indesit washing machine, see the video.