Error F05 in Indesit washing machines

When error F05 appears on the display in Indesit washing machines, many owners of these modern household appliances have questions, and not always there is a universal solution for the problem. There are several reasons for the occurrence of a breakdown of this type, all of them need a thorough diagnosis. What does this mean and how to proceed in a situation when the wash cycle has already started? Let's try to figure it out.

Error F05 in the Indesit washing machine indicates that the unit cannot drain the water normally. At the same time, the equipment may not have an information board - in this case, it issues a breakdown code in the form of flashing indicator lamps on the dashboard. If the Power / Start signal blinks 5 times in a row, then pauses and repeats again, this means an error similar to the combination of letters and numbers on the electronic display. At the same time, the knob will rotate.

The appearance of the F05 error can be noticed at the moments when the technician completes the wash cycle and proceeds to rinsing. In this case, you may notice signs of a problem such as abnormal humming or other sounds. Problems in which the technology may have such "symptoms":

• clogged drainage hose;
• violation of the filter passability;
• malfunction of pumping equipment;
• breakdown of the pressure switch.

Most often, when the F05 error appears on the display in Indesit washing machines, the washing process stops completely, the equipment stops its work, while water can still be seen inside the drum. In this case, it is recommended to make sure that the fault is recognized correctly. Besides, for further diagnostics and troubleshooting, you will have to drain the water in an emergency (forced) mode through a hose or drain pipe... After that, the door is unlocked and it will be possible to take out the laundry by temporarily placing it in a basin or other container.

It is worth considering that the source of problems can also be an external cause. The machine will not be able to drain the water if there is a blockage in the drain. In this case, you will have to resort to the help of plumbing specialists, otherwise difficulties will soon arise with the use of other plumbing fixtures.

When deciding what to do when an F05 error is detected in an Indesit home washing machine, it is important to understand that pinpointing the source of problems can only be done through a complete check of the entire water drainage system. To do this, you need to free it from the liquid and disassemble it.

Technologically, this is the simplest solution to the problem. It will be enough to remove water and laundry by hand, and then proceed to larger actions. Having prepared a bucket for dirty water, you need to place it as close as possible to the area where the drain hose and the sewer riser are attached. After that, the clamp holding the connection is removed, then the stagnant liquid can be allowed to drain.

The drain hose is disconnected from the pump and needs to be checked. First, you need to loosen the clamp holding it so as not to violate the integrity of the flexible pipe. The drain hose of the washing machine is checked for blockages - it is enough to pass a stream of water through it under pressure.If there is contamination, water will not pass, in this case, the product is shown mechanical cleaning by hand. However, even after a complete cleaning, you should not rush to reinstall the hose, it is worth investigating and cleaning the pump additionally, and, if necessary, even replacing it.

The pump is the “heart” of the washing machine's drainage system and is responsible for emptying the drum. If it fails, it will simply not be possible to use the equipment for its intended purpose. Since the drain pump still has to be removed from the housing when the hose is removed, it must also be checked for faults. The procedure will be as follows.

1. Unscrew the fixing screws on the pump housing.
2. The machine, disconnected from the power supply and sewerage system, is moved to the side position. If there is not enough lighting in the bathroom, you can move the unit.
3. Through the bottom part, the pump is freed from all pipeline connections connected to it.
4. The pump is removed and checked for integrity and possible blockages.

Often the cause of the failure of the drain pump is damage to its impeller. In this case, the problem will be observed in the difficulty of its rotation. If this happens, it is imperative to find and eliminate the obstacle that interferes with the free movement of the element. Besides, the pump itself during operation can accumulate debris inside, receive damage incompatible with normal operation. To check, the device will have to be disassembled, cleaned of dirt.

The electrical system of the drain pump is checked with a multimeter. They check all contacts - terminals that, if the connection is broken, can interfere with the normal operation of the equipment. They can be stripped to increase conductivity. In addition, you need to check the resistance of the motor windings with a multimeter.

The pressure switch, or water level sensor, is a part placed in the Indesit technique under the cover of the upper part of the case. It can be accessed by unscrewing only 2 mounting bolts. A round piece will be attached to the angle bracket inside the case and connected to the hose and wires. The cause of a malfunction of the pressure switch can be both a breakdown of the sensor itself and a failure of the tube supplying pressure to it.

If the pressure switch is broken, it is imperative to ensure that this part is replaced as soon as possible. Otherwise, even after a complete wash cycle with water draining in normal mode, the sensor will not receive a signal that the liquid has been removed from the drum.

If not cleaned regularly, the most common cause of blockages is a dirty drain filter. In the car Indesit, he acts as a kind of "trap" for all sorts of garbage. If left unattended, one day the unit display will certainly display error F05. It is worth considering that cleaning work is always carried out in a de-energized washing machine, with the water completely drained from the drum. The filter is located on the back of the equipment, has a removable panel or a swing flap that allows access to it (depending on the model).

Elimination of this breakdown is within the power of even completely inexperienced housewives. Removing the filter from the mount is quite simple: turn it from left to right, and then pull it towards you. After these manipulations, the part will be in the hands of the person performing the maintenance of the equipment. It must be manually cleaned of thread fleece, buttons, and other accumulated debris. Then you can simply rinse the part under the tap.

It is always worth keeping a bucket and rag ready while the drain system is being repaired. Residual water can be found in the most unexpected places and tend to splash out of the unit body.

If the sewer system in a private house is clogged, the blockage can be removed using a special device, which is a long metal cable or wire "brush". In a city apartment, it is better to entrust the solution to the problem to representatives of plumbing services.

Sometimes the problem occurs in the electronic module. In this case, it is imperative to diagnose the board and the contacts suitable for it. To work with this equipment, it is imperative to have skills in soldering parts and handling a multimeter.

How to clean the filter when an F05 error occurs, see below.