How to replace a heating element in a Hotpoint-Ariston washing machine?

The Hotpoint Ariston brand belongs to the world famous Italian concern Indesit, which was created back in 1975 as a small family business. Today, Hotpoint Ariston automated washing machines occupy a leading position in the home appliance market and are highly demanded by customers due to their quality, design and ease of use.

Hotpoint Ariston brand washing machines are easy to maintain, and if it happens that you need to replace the heating element in this unit, anyone who knows how to hold a screwdriver and is familiar with the principles of electrical engineering can cope with this task at home.

For the Hotpoint Ariston washing machine, as well as for other similar machines, the breakdown of a tubular heating element (TEN) is a fairly common phenomenon.

It happens for a variety of reasons:

• the presence of a factory defect in the heating element;
• interruptions in the supply of voltage in power grids;
• the formation of scale due to the content of an excessive amount of mineral salts in the water;
• unstable operation of the thermostat or its complete failure;
• complete disconnection or insufficient contact of the electrical wiring connecting to the heating element;
• actuation of the safety system inside the heating element structure.

The washing machine informs its owner about the presence of damages and malfunctions using a special code.appearing on the control display or by the blinking of the lamp of a certain sensor.

The tubular electric heater serves in the washing machine in order to heat the cold water entering the tank to the temperature set by the parameters of the washing mode. If this element fails for any reason, the water in the machine remains cold, and a full-fledged process of washing under such conditions becomes impossible. In case of such malfunctions, customers of the service department inform the master that the wash cycle becomes too long, and the water remains without heating.

Sometimes the situation may look different - the heating element over time becomes covered with a thick layer of lime deposits and its performance is noticeably reduced.

Before starting repair work, the washing machine must be disconnected from the water supply system and the power supply. For easy access, the machine is moved to an open and spacious area.

To complete the work, you will need to prepare the necessary tools:

• screwdriver - flat and Phillips;
• wrench;
• a device for measuring current resistance - a multimeter.

In Hotpoint Ariston brand washing machines, the heating element is located on the back of the case. To open access to the heating element, you will need to remove the back wall of the machine body. The heating element itself will be located below, under the water tank... For some models, the entire rear wall does not have to be removed; to replace the heating element, it will be enough to remove a small plug to open the revision window, where in the right corner you can see the element you are looking for.

When all the preparatory work has been completed, you can start dismantling and replacing the heating element.

Before removing the heating element in the Hotpoint Ariston brand washing machine, you will need to disconnect the electrical wires from it - there are 4 of them. First, the power contacts are disconnected - these are 2 wires in a red and blue braid. Then the contacts coming from the case are disconnected - this is a yellow-green braided wire. There is a temperature sensor between the power contacts and the case - a small part made of black plastic, it must also be disconnected.

There is a nut in the center of the heating element, a wrench will help you to loosen it. This nut and bolt serves as a rubber seal tensioner that seals the joint. To remove the heating element from the machine, the nut does not need to be completely unscrewed, partial loosening will allow the entire bolt to be sunk deep into the seal.

When replacing the old heating element with a new one, the temperature relay is usually also subject to replacement. But if there is no desire to change it, then you can install the old sensor as well, having previously checked its resistance with a multimeter. When checking multimeter readings should correspond to 30-40 ohms... If the sensor shows a resistance of 1 Ohm, then it is faulty and must be replaced.

So that when installing a new heating element, the rubber seal fits more easily into its place, it can be slightly greased with soapy water. Inside the washing machine, under the water tank, there is a special fastener that works according to the latch method. When installing a new heating element, you need to try to move it deep into the car so that this latch works... During installation, the heating element must sit tightly in the space provided for it and be fixed with sealing rubber using a tension bolt and nut.

After the heating element is installed and secured, you need to connect the temperature sensor and electrical wiring. Then the build quality is checked with a multimeter, and only after that you can put the back wall of the machine body and pour water into the tank to check the operation of the new heating element.

Failure of the heating element most often occurs due to metal corrosion that occurs under the layer of limescale. In addition, scale can affect the rotation of the drum, therefore in regions with high water hardness, washing machine manufacturers recommend using special chemicals that neutralize the formation of scale.

To prevent power outages while using the washing machine, it is recommended to use a voltage stabilizer. Such automatic stationary stabilizers have a low cost, but they reliably protect household appliances from current surges that occur in the power supply network.

In order to maintain the performance of the temperature sensor, which rarely fails, home appliance repair specialists recommend that users of washing machines, when choosing programs for washing, do not use heating at the highest rates, but choose average parameters or slightly above average.With this approach, even if your heating element is already covered with a layer of limescale, the probability of its overheating will be much lower, which means that this important part of the washing machine can last much longer without requiring urgent replacement.

Replacing the heating element in the Hotpoint-Ariston washing machine is presented in the video below.