Error F4 in the ATLANT washing machine: causes and solution to the problem

If the machine does not drain the water, the causes of the malfunction most often have to be looked for directly in its system, especially since self-diagnosis in modern technology is performed quite easily and quickly. How to eliminate the F4 code, and what it means when it appears on the electronic display, why the F4 error in the ATLANT washing machine is dangerous for technology, why, when it is detected, it is impossible to continue washing - these issues should be understood in more detail.

Modern automatic washing units are equipped with an electronic unit, which, before starting the standard cycle, performs a test check of all functions of the device. If problems are identified, an inscription with a code appears on the display, which shows which particular error was detected. The ATLANT washing machine is no exception to the general range.

Error F4 is included in the list of faults, code designations of which are presented in the operating instructions. If it is lost or unavailable, you should know that such an inscription indicates problems with draining water from the tank in normal mode. That is, at the end of the cycle, the unit will simply stop its work. It will not spin or rinse, and the door remains locked because the water used for washing is inside.

The main and most common reason for the appearance of the F4 error in ATLANT washing machines is the failure of the pump - pumping equipment responsible for the effective pumping of water. But there may be other sources of the problem. The car will show F4 on other occasions. Let's list the most common ones.

1. The electronic control unit is out of order. In fact, the error code in this case can be absolutely anything. That is why, having not found breakdowns in other nodes, it is worth returning to this reason. Usually the fault is caused by a flooding of the board or a short circuit after a power surge. In addition, a failure in the firmware can occur due to systemic reasons or due to a factory defect.
2. Error in connecting the drain hose. Most often, this problem manifests itself immediately after the first connection or reinstallation of equipment, especially if these manipulations were performed by a non-professional.
3. The hose is mechanically pinched. Quite often, the body of the machine or a fallen object presses on it.
4. The drain system is clogged. Both the filter and the hose itself can be dirty.
5. Drain pump defective. The water is not pumped out because the pump, which must supply pressure to evacuate it, is broken.
6. The normal operation of the impeller is disturbed. Usually the reason is debris or foreign bodies trapped inside the case.
7. The wiring is faulty. In this case, problems will manifest themselves not only in displaying an error code on the screen.

In order to understand what kind of breakdown caused the malfunction, you need to perform in-depth diagnostics. The F4 error is most often associated with problems in the drain system itself. But first, you need to make sure that what is happening is not a system glitch. It is quite simple to determine this: if, after disconnecting from the power supply for 10-15 minutes, the machine turns on again and begins to regularly discharge water, then this was exactly the problem.

After such a restart, the F4 indicator is no longer displayed, the washing continues from the stage at which it was stopped by the system.

When the cause of the breakdown is not eliminated after a restart, the F4 error in the ATLANT washing machine will persist after a restart. In this case, you need to systematically investigate all possible sources of malfunction. It is important to disconnect the machine from the mains beforehand to avoid electrical injuries.

Next, it is worth checking the drain outlet hose. If it is pinched, has traces of bending, deformation, you should straighten the position of the flexible tube and wait - the water drain produced by the machine will indicate a solution to the problem.

To fix a breakdown of the ATLANT washing machine in the form of an F4 error, you need to thoroughly examine all possible sources of the problem. If the hose does not have external signs of bending, is in the normal position relative to the unit body, you will have to act more radically. The machine is de-energized, the drain hose is disconnected, and the water is drained through the filter. Next, you need to perform a number of actions.

1. The hose is rinsed; if a blockage is found inside, it is mechanically cleaned. Plumbing fixtures can be used. If the sheath is damaged during the removal of the blockage, the hose must be replaced. If after this the patency is restored and the drain works, no further repairs are needed.
2. The drain filter is removed, located behind a special door in the lower right corner. If it gets dirty, the problem with the F4 error may also be relevant. If a blockage is found inside, mechanical cleaning and rinsing of this element with clean water should be performed. Before dismantling work, it is better to put a cloth underneath or substitute a pallet.
3. Before replacing the filter, be sure to check the impeller for mobility. If it is jammed, the system will also generate an F4 error. To remove the blockage, it is recommended to disassemble the pump and remove all foreign bodies. At the same time, the condition of the pump itself is checked - its insulation may be damaged, contamination can be observed that interfere with normal operation.

In the absence of obvious blockages in the drain system of the ATLANT washing machine, the F4 error is most often associated with a malfunction of the electrical components of the system. The problem may be due to poor contact or broken wiring from the pump to the control board.

If, during the repair, the need for replacement of parts or complete dismantling is revealed, the machine is removed from the mountings, moved to a convenient place, and placed on its left side. The broken drain pump is dismantled with a regular screwdriver. First, the chip that connects the wiring is removed, and then the screws or screws are removed that secure the device inside the machine body. Then you can install the new pump in place and fix it in its original position. Proceed in the same way if damage is found on the coupling.

Diagnostics of electrical wiring is carried out using a multimeter. It is necessary if there is no blockage, the parts are completely serviceable, and the F4 error is observed. After dismantling the fasteners holding the pump, all terminals are checked. If a place is identified where there is no contact, the repair consists in replacing the wiring in this area.

The simplest way to prevent a breakdown diagnosed by the ATLANT washing machine as an F4 error is regular preventive maintenance. It is important to carefully inspect the equipment before starting, to avoid getting foreign parts into the drum and the drain system. The drain filter is periodically cleaned even if there are no breakages. In addition, during the repair, it is imperative to use only regular parts.

It is important to consider that usually the F4 error appears on the display of the washing machine only in the middle of the wash cycle, when the rinsing or spinning process starts... If the signal on the display lights up immediately after switching on or at the initial stage, the reason may only be a malfunction of the electronic unit. Repair and replacement of the board yourself should be done only if you have sufficient experience and practice in working with electrical equipment.

How to repair your Atlant washing machine yourself, see below.