How to insert staples into a construction stapler?

Very often, in the construction or repair of various surfaces, it becomes necessary to fasten different kinds of materials together. One of the ways that can help solve this problem is a construction stapler.

But in order for it to do its job correctly, it needs to be serviced. More precisely, from time to time you need to recharge it by filling it with new staples. Let's try to figure out how to correctly insert the staples into a construction stapler, replace one type of consumables with another, and also refuel other models of this device.

Structurally, all manual construction staplers are basically the same. They have a lever-type handle, thanks to which pressing is carried out. At the bottom of the device there is a plate made of metal. It is thanks to her that you can open the receiver in order to subsequently shove the staples there.

Before purchasing certain staples in a specialized store, you should clarify which ones are needed for the stapler model, what is available. Most often, you can find out such information on the body of the device, which indicates the size, as well as the type of brackets that can be used here.

For example, a width of 1.2 centimeters and a depth of 0.6-1.4 centimeters are indicated on the body of the device. This means that here you can use brackets only with these parameters and no others. Models of a different size simply will not fit into the receiver.

To put the staples in the stapler, you must first open the metal plate on the back. You will need to take it with your index and thumb on both sides, then pull it in your direction and slightly down. This is how we push up the metal foot located on the back of the plate. After that, you need to pull out a metal spring, which is similar to the one that is present in the simplest office-type stapler.

If there are still old staples in the stapler and there is a need to change them, then in this case they will simply fall out when the spring is pulled out. If they are absent, then it is required to install new ones so that this device can be further used.

Staples remain to be installed in the receiver, which has the shape of the letter P. After that, you need to install the spring back and close the foot. This completes the hand stapler threading process.

As already stated, Before loading the stapler, make sure that the staples you have selected are the correct size for the stapler. Information about their characteristics is usually placed on the packaging. But different models may have certain charging characteristics.

For example, you will need to use tweezers to refill the mini stapler. Here the staples will be very small and it will be difficult to place them correctly in the corresponding hole with your fingers.

So, for refueling most models, you only need to have staples and the device itself. Let's analyze the stages of this process.

• Determine what type of fixture is available. To do this, you should see how many sheets can be stitched by the device at the same time.The most primitive from this point of view will be pocket-type staplers. They can only staple up to a dozen sheets. Hand-held models for the office can hold up to 30 sheets, and desktop-vertical or horizontal with plastic or rubber soles - up to 50 units. Saddle stitch models can bind up to 150 sheets, and typographic models, which differ in maximum sewing depth, 250 sheets at a time.

• After that, it is required to determine the dimensions of the staples, which are really suitable for the existing model of the stapler. Staples, or, as many call them, paper clips, can be of various types: 24 by 6, # 10, and so on. Their numbers are usually written on the pack. They are packed in packs of 500, 1000 or 2000 units.

• To charge the stapler with suitable staples, you will need to bend the cover. It is usually connected by a plastic piece to a spring. The plastic part clamps the staple to the opposite edge of the metal groove where the staples are placed. Opening the lid pulls the spring, and therefore the plastic part. This makes it possible to free up space for new staples.

• It is required to take the staple section and place it in the aforementioned groove so that the ends of the staples point downward. Now close the lid and click once to test with a stapler. If the staple has fallen out of the corresponding hole with the concave tips inward, then the stapler has been charged correctly. If this did not happen, or the bracket is bent incorrectly, then the steps should be repeated, or the device should be replaced.

If you need to charge an ordinary stationery stapler, then the process will be almost the same:

• you should first inspect the device and find information on it about which brackets can be used here;

• it is required to purchase consumables of the exact type, the number of which is present on the stapler;

• open the device, insert staples of the required size into it, and you can use it.

If it is required to charge a construction pneumatic device, then the algorithm of actions will be different.

• The device should be locked. This is done in order to avoid accidental activation.

• Now you need to press a special key that will open the tray where the staples should be located. Depending on the model, not such a mechanism may be provided, but an analog in which the tray cover will slide out of the handle.

• It is required to make sure once again that the device does not accidentally turn on.

• The staples must be inserted into the tray so that their legs are located towards the person. After installing them, check that they are level.

• Now the tray needs to be closed.

• The working part of the tool needs to be turned over to the surface of the material.

• We remove the device from the lock - and you can start using it.

To refuel a large stationery stapler, proceed in a specific order.

• It is necessary to bend the stapler cover, made of plastic, which is held by a spring. Opening the lid will pull on the spring and the resulting space will be the groove for the staples. Many large staplers of this type have latches that need to be pushed back.

• Take 1 section of staples, insert them into the groove so that the ends point down.

• We close the cover of the device.

• It is required for them to click once without paper. If a paper clip falls out with bent arms, then this proves that everything was done correctly.

If you need to refuel the mini-stapler, then this will be much easier to do than refueling any other model. Here you just need to lift the plastic cover up and back. Then you can insert the staples into the groove. When the charging process is complete, you just need to close the stapler and start using it.

If we talk about recommendations, then we can name a few expert advice.

• If the tool does not finish off or does not shoot the staples, then you will need to tighten the spring a little. Its weakening as you use such a tool is completely normal.

• If the construction stapler bends the staples, then you can try to adjust the bolt, which is responsible for the tension of the spring. If the situation has not been corrected, then perhaps the selected staples simply do not correspond to the structure of the material for which they are used. Then you can try to replace consumables with similar ones, but made of hardened steel.

• If nothing comes out of the stapler, or it happens with great difficulty, then, with a high degree of probability, the point is in the striker. Most likely, he simply rounded, and it needs to be sharpened a little.

How to insert staples into the stapler, see the video.