Circular shears for screwdriver

Disc shears for metal is a technical device designed for cutting thin-walled sheet metal. Working elements, in this case, are rotating parts. They are self-propelled discs made of high-strength material, sharpened along the edge. The process of cutting the material with this device occurs due to the linear-translational squeezing of the sheet. The device allows you to make an even cut without deforming the workpiece.

There are disc shears for metal, powered by a screwdriver drive. They are a replaceable attachment that expands the functionality of the power tool.

This screwdriver attachment allows you to cut sheet metal without damaging it. Doing the same with a grinder has a negative effect on the metal workpiece. At the moment the abrasive disc passes through the metal, its edges are subjected to friction in the area of ​​the cut, which creates conditions for increasing temperature indicators to critical levels. Overheating of the material occurs and its composite structure is disrupted. If it was covered with a galvanized layer, it loses its properties and the metal begins to easily react to aggressive environmental influences - to oxidize, rust.

In addition, the abrasive method of sawing causes burrs at the edges of the saw cut. To remove them, additional grinding is performed, which leads to a waste of time, a deterioration in the quality of the cutting line, a negative effect of temperature on the metal and increased wear of the power tool and its rotating parts.

Circular shears make it possible to cut metal, eliminating the above-described negative factors. At the same time, it becomes possible to vary the lines - to make curved sawing.

This nozzle works on the principle of power transmission through a gear system. The efficiency of the removable add-on is increased by combining the efficiency of the screwdriver gearbox with the same indicator of the gear mechanism of the nozzle itself. The force transmitted to the circular knives is doubled, which is a key factor in cutting performance.

Scissors attachments are divided into two types:

• two-disk;
• multi-disk.

The photo shows the scheme of operation of the double-disc shears, however, the principle of the arrangement of the cutting discs may differ. In some cases, one of the knives is tilted, in the other both knives are tilted, and in the third they are set directly in relation to each other. The presence or absence of a tilt angle is determined by the purpose of the cutting attachment. The angle depends on how the cut will be carried out, as well as the permissible parameters of the metal thickness.

Scissors, powered by a screwdriver drive, are equipped with a pulley that is clamped into the chuck of the power tool. The pulley rotates, transmitting mechanical force to the gearbox located inside the nozzle body. The force causes the movable blade to rotate.

A special mount departs from the main body of the case, holding the second disk on itself. It can be installed as a movable or stationary element.The design of the mount assumes the function of adjusting the gap between the discs.

The gap is determined by the thickness of the metal sheet that will be cut.

A metal stop leaves the body. It is designed to keep the attachment in a fixed position. Its absence will lead to radial rotation of the entire mechanism. To eliminate this effect, the stop is attached to the lower part of the screwdriver handle - just above the battery.

During the rotation of the screwdriver gearbox, the nozzle will begin to make a corresponding circular movement. This movement is stopped by the fact that the stopper rests against the handle of the power tool. After that, the rotational force is transmitted to the gear mechanism of the nozzle. In order for the stop to not dangle and fit snugly to the handle, it has a special hook with the ability to change its position in space.

The device of this device is very simple. It lacks complex mechanical blocks that would require specialized knowledge of operating methods.

The quality of the nozzle and its durability depend on the manufacturer and the material from which it is made. On the Russian "iron" market, you can find names marked with data from a domestic manufacturer. However, most of these attachments or their parts are made in China. The fact that the device is assembled on the territory of the Russian Federation does not guarantee its quality.

For Chinese models, the following features are characteristic:

• poor quality of the material;
• poor build;
• low price.

The main characteristic of this nozzle, which determines the efficiency of its operation, is the alloy from which the cutting elements are made - knives. If they are made of low carbon steel, this will permanently blunt the knives, which will reduce tool performance and cut quality. Such discs require regular sharpening.

Of no small importance is the material from which the nozzle body is made. During operation, high power loads are applied to all parts of the body. This is due to the presence of gear mechanisms built into the system. A huge rotational force is transmitted through the gearbox at low speeds. The soft material of the body may not withstand the load, which will lead to the occurrence of destructive damage. The result of this situation can be a complete failure of this device.

When choosing disk shears, it is important to pay attention to the build quality and the state of the rotation units of the mechanism joints. Backlash, cracks, chips and other defects are unacceptable. It is checked that there is a sufficient amount of lubricant applied to the moving parts of the nozzle.

In the absence of good lubrication, disassemble the device, remove signs of poor quality lubricant and apply a new one. It is advisable to use a grease that is resistant to high temperatures, since the body of the device and other parts of it become hot during operation.

The scissor attachment is easy to use. In order to use it, you need to insert the stem of the nozzle into the screwdriver chuck (it is advisable to use a screwdriver, since it works at low speeds). Provide a high level of stem tightening in the chuck.

• Install the stop by fixing its end to the screwdriver handle using movable fasteners.
• Adjust the gap between the cutting discs.

Adjustment is made by loosening the adjusting bolt, applying a metal sample to the discs, setting the knives to the desired position, and retightening the bolt.

The distance between the circular knives should be 0.3-0.5 mm less than the thickness of the metal sheet.

Check the operation of the device by a test run. For correctness of the test results, you can cut a metal wire of the appropriate diameter. During the cut, there should be no signs of runout, galling and other factors that can reduce the accuracy and quality of the cut.

Start cutting from the edge of the sheet. Drive the device slowly, without sudden movements. In this case, the workpiece must be firmly fixed so that vibration and arbitrary shifts do not violate the cutting line.

When performing work with circular shears on a screwdriver, it is important to observe all the required safety measures. Their list includes the main ones:

• protect the organs of vision with specialized glasses;
• use gloves to protect palms from sharp metal;
• have specialized clothing and footwear that is resistant to destructive influences;
• avoid contact of gloves and parts of clothing with rotating parts of scissors and a screwdriver;
• do not use the power tool continuously.