Features of trellis for blackberry

Experienced gardeners know that watering and heat cannot be used to achieve higher yields. In stock, each of them always has a few tricks to improve the quality and quantity of the crop. These techniques include installing trellises on the beds - culture-supporting structures that do not allow the shoots of highly overgrown plants (blackberries, cucumbers, tomatoes) to lie on the ground.

If vegetables with a strong skin can do without a trellis, then blackberries, like some other berries that are climbing plants, are more than necessary. The fact is that the delicate skin of the berries, in contact with the ground, quickly begins to rot. They become the cause of the accumulation of insects living in the ground, which quickly switch to other fruits.

Gardeners identified the following advantages of using a trellis in the country:

• simplifies care and harvesting, water when irrigated goes directly to the root, weeds and dry branches are clearly visible, it is easier to prune the bush;
• allows you to prevent rotting of the root system and fruits;
• if there is a need for top dressing or tillage, then the fertilizer gets to its intended purpose, the raised branches allow you to easily carry out hilling;
• the presence of trellises in the beds with blackberries allows the culture to grow not chaotically, but strictly in rows;
• beds with tied bushes always look more aesthetically pleasing.

It should be noted that tapestries can be factory-made, or you can make them yourself. But when choosing a device, experienced gardeners recommend not to be guided by this, but to build on the size of the berry plantation. In small areas, it is recommended to use single-lane trellis, and on large farm plantations, two-lane trellis designs will be appropriate.

There are many varieties of single-strip trellises: fan-shaped, straight horizontal or inclined, arched and many others. The peculiarity of each presented variety is not so much in a practical sense, so much in an aesthetic function (they are erected mainly for a beautiful design of a garden plot).

The design is simple, therefore if necessary, you can easily make a trellis with your own hands. It is a multi-row wire stretched between the posts in 1 plane.

The two-lane trellis, in contrast to the single-lane, have 2 parallel planes with multi-row represented by wire. This model allows not only to support hanging branches, but also to improve the formation of the bush. The first row of rope (wire) is pulled at a distance of 50 cm from the ground, and the last - at a height of 2 meters from the ground.

This type of trellis also has several options for creating. Only this is mainly not a decorative design for a garden, but a variety that can hold strong branches of bushes, directing them to simplify harvesting to the right and left.

The easiest way is to make a T-shaped version, which is a pillar, a crossbar is nailed to it so that the whole structure resembles the letter "T"... If desired, such crossbars can be placed up to 3 pieces. The length of each top bar will be more than the previous one by half a meter (the length of the shortest bottom rung is 0.5 m). This will allow, without changing the design, to tie up the bush at different stages: the lower ones are intended for slightly overgrown bushes, the middle ones for slightly overgrown ones, and the fluffy side shoots are attached to the uppermost one.

But thanks to such models, the yield will be higher, since the bush lays down evenly to the right and left. Due to this, its central part receives an even amount of light and heat.

The most difficult Y-shaped model to manufacture can be movable and fixed... The production of a mobile version is due to its use in the northern regions of the country, where the culture needs to be well covered for the winter.

The model is a main pillar, to which, at a distance of 1 m from the ground, side crossbars are attached in different directions. If we are talking about a movable structure, then thanks to the hinge fastening, these rungs move. The movable mechanism allows the necessary crossbar with a bush suspended from it to be lowered to the ground closer to winter. On the ground, the culture is covered with rags, and in this position it meets the winter.

Homemade and factory trellis for blackberries have almost the same dimensions, which are determined by the average permissible length and width of the bush.

In addition, the height of the structure is due to the convenience of harvesting. It is desirable that it does not exceed 2 meters. Amateur gardeners recommend orienting the height to the growth of a person, which will allow you to quickly and conveniently harvest.

As for the length of the beams of the T-shaped models, as noted above, the indicator can be equal to 0.5, 1, 1.5 m.The length of the beams of the V-shaped and Y-shaped models is 2 m, and the distance between them is 90 cm ...

These are the indicators that are determined over time by specialists.... Thanks to the figures presented, blackberry bushes can be properly fixed on all sides.

Factory tapestries are often made of polymer materials, which makes them immune to moisture, sun and sudden temperature changes. To make a homemade device the same invulnerable, you can use plastic pipes, pieces of PVC panels and other polypropylene improvised means for manufacturing.

Wooden trellises are the easiest to make. In addition, the method is considered less costly, since several unnecessary bars and rails, as well as nails with a hammer, will always be found in the country.

Wire or rope is used as fasteners. But in wooden models, it can be replaced with crossbars made of thin slats.

When choosing a material, you need to take into account that rust will quickly appear on metal products, and devices made of wood are subject to decay due to weather conditions.

Plastic is the most resistant material to environmental influences, which is not exposed to negative influences from the outside (unless the drawing on it can fade in the sun). But plastic is not easy to work with as it breaks apart quickly.Especially if you use large nails for the connection. If there are no small nails, or used parts are used as plastic material, then it is better not to risk it, but use glue intended for outdoor work to connect.

It was already noted above that the easiest way is to make a single-strip trellis for blackberries with your own hands. Having decided on the model and properly planning the design diagram, you can start drawing up simple drawings to calculate the required amount of material. For manufacturing, you will need pillars with a height of at least 3 m (they can be wooden or metal) and wire with a thickness of 4 to 6 mm.

To install the pillars, pits about one meter deep are dug along the edges of the beds (if the soil is not clayey, then a depth of half a meter is permissible). If the bed is too long, then we break it into equivalent segments. It is important that the distance between the posts is 5 to 6 m, but not more, otherwise the wire will sag.

For better stability, the pillars are placed in the center of the pit and covered with rubble or gravel with earth, after which everything must be tamped well. If the earth has an excess of sand, which makes it loose, then it is recommended to fill the pillars with cement mortar.

Recently, a single-strip trellis has been gaining popularity, made of plastic pipes used for heating in an apartment. If you purchase the required number of pipes and corner joints sold with them, then you can build a single-row trellis without using a hammer with nails and glue.

Since the garter influences the formation and maintenance of the bush, it must be bound correctly in order to simplify the cultivation and get a higher yield. It is recommended to form the planted bushes on a fan-shaped trellis, planting them at a distance of 2 m from each other.

With further care of the crop, you should remember that there are 3 ways of tying.

• Weave... With such a garter, the shoots, intertwining, are laid on 3 tiers. After that, we move the growth aside and put it on the 4th tier.
• Fan garter (applicable to crops aged from one year and above). Its essence lies in the fact that last year's shoots, laid in the form of a fan, are attached to the first 3 lines, and the 4th line is set aside for new shoots.
• Unilateral tilt... Last year's shoots, as in the case of the fan garter, are attached to the first 3 tiers, and the young shoots are sent to the other side.

If it is necessary to tie, and not intertwine, it is not recommended to use hard or too thin threads (fishing line or nylon), as they can cause cuts.

See below for tips on making blackberry trellis.