Construction one-wheeled reinforced wheelbarrows

Any construction and overhaul of buildings is difficult to imagine without carrying loads. It is not always possible or very difficult to do this manually. Therefore, it is required to use auxiliary mechanisms.

It is advisable to start a conversation about reinforced construction wheelbarrows by comparing them with conventional models. So, for a simple cart, the frame is made of steel with a thickness of 0.12-0.15 cm.When creating a more powerful structure, they take metal not thinner than 0.2 cm... Additionally use double bracket increased power, and frame bends are equipped with plates... Steel for the body of a reinforced wheelbarrow is also used more powerful, not 0.07-0.08, but at least 0.09 cm.

The support is put on the frame with handles so that its front part is on the outside of the frame. In this case, the back lobe, close to the handles, should be located from the inside of the same frame. Of course, all this is only approximate and general information, more accurate information can be obtained from the instruction manual. Therefore, before buying, you need to consult with specialists.

When it comes to building one-wheeled reinforced wheelbarrows, it is useful to pay attention to the model 331-ZP. According to the manufacturer, this device turns out to be attractive for any repair and construction, and in other cases - for moving heavy loads. Therefore, you can confidently use the 331-ZP when working in the garden, in the garden, for the removal of household waste.

For the manufacture of the frame is taken pipe with an outer section of 3.2 cm... The thickness of the steel is 0.2 cm. To make it even more reliable, longitudinal plates are placed. Importantly, Italian dyeing equipment is used in the production process. The body of the wheelbarrow accommodates 110 liters of cargo, in the manufacture of the main part of the body, metal with a thickness of 0.09 cm was used.

The developers also took care of strengthening the propeller brackets. The wheelbarrow rides on a wide wheel with an outer section of 15 inches. A pair of bearings has a 1.9 cm bore diameter. This combination of components allows movement 250 kg cargo... In this case, the load on the hands is a maximum of 15% of the transported mass.

Reinforced carriage structure allows you to use it:

• builders;
• landscape designers;
• housing and maintenance services;
• road construction organizations;
• individuals.

Compared to standard trolleys, the metal is 100% thicker. All vulnerabilities have been carefully improved. Therefore, it is possible to use the device longer in the most intense mode. Even if you have to transport at an accelerated pace large volumes of sand, cement and concrete mortar, the car will work perfectly.

The Belamos 457P modification is equipped with a steel body with a volume of 85 liters and a pneumatic wheel with a diameter of 38 cm... Made in Russia, the structure can move up to 80 kg of cargo. The Chinese model "Rambo" is also equipped with a steel body and identical carrying capacity. However, the body's capacity is only 65 liters.

Made of galvanized steel, the FIT 77555 takes on board up to 140 kg... One of the most powerful versions, the Haemmerlin Cargo 90 MG P, is equipped with cast wheels with a section of 39 cm, thanks to which it can carry up to 200 kg.

The vast majority of versions (as can be seen from the above review) can carry from 100 to 150 kg of cargo. In this case, the capacity of the bodies is 70 or 80 liters. The most powerful structures, which take 200 kg, are equipped with reinforced frames... Their characteristic difference is, which is quite natural, the metal of increased thickness. Important: it should be checked for rust and other defects.

A truly reliable wheelbarrow will not budge if you press on it with force, first placing it at a low angle. As for the wheels, there are no special requirements. But there are relatively minor nuances that can "poison" life. So, plastics all types suffer from air temperature changes. If you have to carry more cargo, you need to choose ne pneumatic, but cast options.

However, all these subtleties are largely subjective. But the choice of pens is much more serious. If you make a mistake with it, the workload will be very high. Experts advise to first see if it is convenient to stand between the handles. Then the wheelbarrow is put in the working position, and at the same time there should not be any painful sensations from the beginning.

According to experts, great frame spout length... It is good if it extends slightly beyond the edge of the trough or is at the same level with it. A construction wheelbarrow, unlike a garden one, must be equipped with longitudinal stiffeners... It also has a side flange.

The following video will tell you about the advantages of a construction one-wheel wheelbarrow.