How to fix a partition from rails with your own hands?

Knowing how to fix a partition made of rails with your own hands is necessary for almost every owner of an apartment or a country house. Correctly attaching a slatted partition is a great method for zoning a room. You can also carry out the installation of a wooden interior partition, decorating the space of the room at the same time.

Installation of an interior divider made of wooden slats can be done only by experienced, well-trained people. If the installation is carried out on a plank floor or on a laminate up to 1 cm thick, drilling is not required. But to attach the partition to the concrete floor, which is usually necessary for work on the ceiling, you will need to prepare at least 8 embedded holes: half on the floor, half on the ceiling.

Reiki should be taken with a reserve of about 3 m in length. Cutting must be done directly at the place of work, after accurate fitting and fitting. The fact is that the ceilings have unequal heights, and sometimes they also differ in a pronounced or even ambiguous slope.

A complete mounting kit includes:

• pencil (marker, chalk);

• the wooden slats themselves;

• structures for the frame;

• drill or hammer drill;

• drill;

• fasteners;

• building level or the already mentioned plumb line.

A do-it-yourself partition of slats can be made both on the basis of bars and from MDF. It is advisable to veneer the second material with oak or ash. You can also take parts of the furniture board as a basis. A typical sequence of manipulations is as follows:

• punch holes for dowels;

• screw in these fasteners;

• put studs;

• put bars or boards.

To install the partition on the walls and ceiling it was more convenient, you can purchase buffels with special grooves. This mount is in demand among designers. Fastening the slatted partition is advisable for zoning in those places where the interior cannot be burdened. Connecting the slats vertically and horizontally is equally practical. It is allowed to use small jumpers for a bundle.

It is very important to fix the partition to the floor using embedded elements. Installation can be done in various ways. If you want to make a movable screen yourself, it is recommended to use wooden guides. You can fix them with self-tapping screws or screws. As soon as they are installed on the floor and on the ceiling, you can immediately insert the finished panel into the grooves.

After drilling holes in the wall and removing dust, pour glue into it and insert pins. Further, in order to mount decorative interior partitions, you need:

• glue the holes in the bar;

• put buffels on the wall;

• attach the top of the product;

• mount a decorative bar.

Putting partitions made of wood into a room on hidden fasteners means significantly improving the perception of the interior. For this purpose you need:

• mark the fixation points on the ceiling;

• apply the same markings to the floor using a plumb line;

• fix the strips or corners to the floor and ceiling using self-tapping screws;

• fix the strips to the fastening strips using liquid nails or polyvinyl acetate;

• in the case of a massive partition - additionally put nails or self-tapping screws;

• eliminate visual defects using putty or furniture wax (deformations of MDF veneer are eliminated using special snap-on inserts).

A separate topic is how to integrate a partition into a stretch ceiling. Sliding partitions are easiest to install, because in this case, the ceiling structure is not directly connected to the doors at all.

Important: this method is effective only if the repair has recently begun and the stretch ceiling has yet to be installed. Guides are placed on the rough ceiling layer, which will be used by the sliding partition.

The timber is also mounted on rough ceilings, but with a slight indent. A profile is mounted to this bar and the ceiling itself is installed on it. Only after its installation do they work with a partition. An important advantage is that repair and replacement of these parts can be done autonomously. An alternative option is also used when the ceiling has not yet been delivered, but in this case the order of work changes:

• installation of a false panel on the ceiling;

• attaching a reinforcing bar to this panel;

• door installation;

• installation of the ceiling.

Sometimes the partition is mounted after the completion of the repair - to highlight a specific area. First of all, a stretch ceiling structure is installed. And already the guiding parts of the partition are attached to it. A high-quality timber is attached to a certain place. A profile frame is made and the canvas is stretched over the bar.

In the selected place, special stickers are glued. Their use will eliminate breaks when punctured by tension cloths. The guides for the partition are screwed onto self-tapping screws. Important: with all the advantages of this method, there is also a minus - the subsequent replacement of the stretch ceiling is either impossible at all, or turns into a "series of adventures".

There is another option, how to mount the partition when there is already a canvas. The technology is as follows:

• remove the coating on one edge;

• fix the mortgage board;

• return the ceiling structure to its place;

• mark the fixing point of the guide, in advance combining it and the embedded element;

• put stickers;

• pierce the plugs with self-tapping screws.

It will not be difficult to attach the rail to the wall and ceiling through the method. The cost of this approach is also relatively low. However, one must understand that you have to drill the wall, and the selection of a plug that matches the color is not so easy. Installation on glue (alternative can be considered "liquid nails") is different:

• the durability of the lath coating;

• simplicity;

• dependence on the adhesive parameters of the bond;

• unsuitable for uneven ceilings;

• low suitability for heavy slats - they can come off.

The use of dowels and glue helps to keep the lath coating intact. Special holes for them are made in an industrial environment with maximum precision. This is definitely a reliable fixation method. However, you will need to drill holes. In addition, only trained installers can do the job correctly.

Find out in advance the location of the wiring, gas, water and sewer communications.

For information on how to make a partition from rails yourself, see the video.