How to make a boombox with your own hands?

Content
  1. Peculiarities
  2. Necessary materials
  3. How to assemble?

It is not difficult to make a boombox out of improvised means with your own hands, a portable column. Requires a minimum of tools and a small amount of working time. What is the best place to start in order to get a product at the level of world standards?

Peculiarities

The boombox is a small but powerful music speaker that has a separate power supply. To create it, the following is required.

  • Board 18 mm thick.
  • Plywood 5 mm (outer front panel).
  • Plywood 12 mm (back panel).
  • Background tube 42 mm.
  • Plexiglass.
  • Fasteners (self-tapping screws, furniture confirmations).
  • Joiner's glue and super cement glue.
  • Solder.
  • Paint in a bottle.
  • Clamps.
  • Battery 12 volt, 7.3 A / h (you can take it from the laptop power supply).

Charging 1 A / h. The sound is reproduced from the car radio Pioneer MV 194 UB. The speakers have AV PB-64.2. Dimensions 152 x 192 x 642 mm. Weight 6.5 kg. You can take speakers for high frequencies - 17 cm, for low frequencies 22 cm. You should pay attention to the wiring coming from the line-out. It is better to put its shielded wiring and remove the power supply. It is permissible to think about increasing the volume of the container itself (box). Some craftsmen put cotton wool or a bag filled with foam rubber in the space, then the sound can change for the better.

The holes for the speakers are cut with a milling cutter, which can be up to 46 °.

It is important to calculate the correct dimensions of the panels so that they match, there would be no distortions.

When gluing the panels, it is recommended to use clamps, the back cover is mounted at the end, after all the wiring has been installed. The plywood body is treated with a universal bactericidal primer before painting.

Necessary materials

To make a boombox from a car radio that has served its life, it is recommended to first remove the speakers. This requires:

  • soldering iron;
  • screwdriver;
  • scissors.

Tools required:

  • drill;
  • Bulgarian;
  • screwdrivers (Phillips simple);
  • scissors, knife;
  • nippers;
  • pliers;
  • glue;
  • self-tapping screws, bolts "3" mm.

The power of each speaker can be 5 watts each, have 4 ohms. The speakers are housed in a new housing that can be made out of a cardboard box. It is permissible to make a container from an aluminum-wooden case, which once contained a set of Chinese modules. Some craftsmen make the case out of plywood. What is needed to make a boombox from an old radio tape recorder:

  • speakers from 2 to 6 pieces;
  • box;
  • amplifier;
  • Li-pol charger;
  • switch;
  • indicator showing the charge level.

    First, points are outlined for the speakers. The drill "3" makes holes. Install the speakers, use 3 mm bolts. Installing the driver. Holes for fastening are cut into the case:

    • indicator;
    • power buttons;
    • volume control;
    • audio jack that provides an audio signal;
    • connector, it provides charging of the lithium device.

    It is important to see that all parts are tightly fixed, and that there are no slots in the case. It is especially recommended to pay particular attention to the joints. To seal the extra holes, it is good to use silicone, it fixes securely and creates a reliable tightness of the container.

    Now it's the turn of the electronic filling. Install the button on the battery tester, it will glow during operation. Another resistor (1 kOhm) is mounted on the switch, then the backlight can work, which will be clearly visible... A connector for the jack is soldered from the board, we switch the wires to the jack of the future boombox.

    The amplifier is connected to a 12 volt charger. The fan is soldered directly to the amplifier connector. The potentiometer can be further extended using a cable. All parts are placed in a container. Some elements can be fixed with tape or glue.

    We assemble from 4 to 6 speakers, each with 4 ohms. We connect all audio units to one two-channel amplifier. Option one: turn off the speakers in series (we connect the minus of the first speaker to the "+" of the second, then minus the second with the plus of the third, etc.). It will turn out, in the end, the sums of 24 Ohm - this is a lot, it is necessary to reduce the parameters.

    If connected in parallel, the resistor will be extremely small, which does not always meet the required requirements. Therefore, you need to combine the elements. The total power will be about 30 watts. If two channels are connected, the power will be increased. As you can see, if we assemble a homemade boombox from a car radio, then difficulties should not arise, structurally this product is simple.

    How to assemble?

    Truck Bed Liner

    For a homemade boombox, you can make a case with a thickness of 20 mm and paint the outside. The result can be very good. It is recommended to make drawings in advance in order to accurately calculate all dimensions. Before the portable boombox starts working, the surface should be sanded, for this, sandpaper is used sequentially:

    • 122 grit;
    • 230 grit;
    • 410 grit

    Sealing is an important topic, there should be no extra slots between the cabinet and the speakers. For these purposes, a 3d printer and special software are used.

    Tinkercad

    Small rings (4-6 pcs.) Are printed and fixed with hot melt glue. A pause should be paused for a day so that the glue is fixed. Goggles, respirator and gloves should be used for painting. It is best to paint in a technical room (garage, warehouse, etc.). Obviously, you will have to do several layers before "putting" the second layer. Wait for the previous ones to dry. It takes at least 3 days to dry the paint.

    Upon closer examination, it becomes obvious: making a "branded" boom-box is not technologically difficult, all components are dismantled from old audio equipment. The materials to make the box are inexpensive.

    It is only important to calculate everything in advance and draw up the correct diagram of the device.

    For information on how to make a boombox with your own hands, see the next video.

    no comments

    The comment was sent successfully.

    Kitchen

    Bedroom

    Furniture