All about refueling Canon printers

Canon printing equipment deserves close attention. It is worth learning everything about refueling printers of this brand. This will eliminate many ridiculous mistakes and problems in the operation of equipment.

The most important rule is to try to avoid refueling, but it is better to change cartridges. If, nevertheless, it is decided to refill the devices, it is necessary to consider how many times the cartridges can be used after refueling. Before refueling a Canon printer, you need to find out which cartridges are used in a particular device model. The capacity of the ink accumulators can vary greatly depending on the specific modification. The difference sometimes also applies to the design of the top covers. Time to refill PIXMA printers:

• when streaks appear during the printing process;

• at the sudden end of printing;

• with the disappearance of flowers;

• with severe pallor of any of the paints.

The procedure must be carried out thoughtfully and carefully. For her, you need to allocate time with a margin, so that nothing interferes and does not distract. Since the cartridges are refilled outside the printer, it is worth considering a free space where you can put them without any risk. Ink selection - a purely personal matter for each user. Products from different manufacturers are more or less the same in quality.

It should be borne in mind that the procedure must be performed as quickly as possible.... The ink head removed from the air may dry out. In this case, it cannot be used.

Holes in monoblock cartridges cannot be sealed with electrical tape, stationery tape of any color and width.... The glue on these tapes will simply block the ink exit channels. When it is not possible to use specially designed adhesive tape, it is required to wrap the cartridges for a while in wet cotton wipes. Can also be used for temporary storage plastic bagslightly moistened from the inside and tightly tied at the neck.

All-in-one cartridges should never be stored empty. And those that allow you to wait for several hours, it is advisable to lay out on a soft napkin before the procedure. It is impregnated with flushing or reducing fluids.

A laser printer is refueled slightly differently than its inkjet counterpart. The toner is selected individually for each model. Compatible devices are listed on the bottles themselves. It is undesirable to buy the cheapest powder possible. And, of course, you must strictly follow the instructions, and also work with the utmost care.

Refilling the cartridge yourself at home (both with black ink and color ink) is not too difficult. Special refueling kits help to simplify the work... They cost a little more than traditional "cans", but they are much more convenient. It is imperative to work on a flat surface. Before refilling the cartridge yourself, you need to remove everything that might interfere from this surface.

Ink of a separate color is taken into the syringes. Important: black dye is taken in 9-10 ml, and colored dye - 3-4 ml maximum. It is advisable to read in advance how to open the printer cover. In order to properly change the paint with your own hands, you need to take the cartridges strictly one at a time. Trying to work with several at once, instead of speeding up the case, you can only get additional problems.

First of all, you need to remove the label on the case using a clerical knife. It hides a small air channel. The passage is increased using a drill or an awl so that the syringe needle passes. You do not need to throw away the stickers as they will have to be replaced anyway.

The needles are inserted 1, maximum 2 cm into the hole. The entry angle is 45 degrees. The piston should be pressed smoothly. The process is stopped immediately when the ink comes out. The excess is pumped back into the syringe, and the cartridge body is wiped with wipes. It is recommended to carefully look at what color of paint to add where.

It is worth remembering that just starting the printer is sometimes not enough. The system indicates that paint is still missing. The reason is simple: this is how the fingerprint counter works. This indicator is built into a special chip or located inside the printer. Designers provide that one refueling is enough for a certain number of pages and sheets. And even if the paint was added, the system itself does not know how to properly handle this situation and update the information.

Simply turning off ink volume control would void your warranty. But sometimes there is simply no other choice but to reboot the printer. In the case of Canon Pixma, you need to hold down the "Cancel" or "Stop" button from 5 to 20 seconds. When this is done, the printer is turned off and on again. Additionally, you should perform a software cleaning of the nozzles.

What to do if the printer does not see ink after refueling is already clear. But the problem is not always solved so simply and easily. Sometimes the reason a printer shows an empty cartridge is because the wrong ink tanks are being used. They are not necessarily intended for other models.Even by simply swapping different colors, they get the same situation. It is imperative that you familiarize yourself with the "printer and cartridge compatibility card" on the site before buying.

Sometimes the system does not recognize the cartridges simply because the protective film has not been removed from them. You also need to remember that cartridges are installed before click... If it is missing, it is likely either damage to the case, or deformation of the carriage. The carriage can only be repaired in a special workshop. Another likely problem is hit of some small objectsbreaking the contact of the cartridge with the carriage.

If streaking occurs, it usually indicates that the cartridge is in poor condition. You can check it by shaking it over unnecessary paper.... It is also worth checking how clean the encoder tape is. Only special liquids should be used for cleaning, but not plain water.

The pallor of the image means that you need to check:

• possible ink leaks;

• enabling the economy mode (it will have to be disabled in the settings);

• the condition of the stove rollers (how clean they are);

• condition of photoconductors of laser models;

• cleanliness of cartridges.

The refueling process for the Canon Pixma iP7240 printer is demonstrated in the following video.