Stretch ceiling installation tools

Stretch ceilings are currently popular during renovations. This is because the design of such ceilings is easy to install and affordable. Correct installation can be done with the right tools.

To carry out the process of strengthening the tensioning system requires some specific knowledge and experience. A number of accessories are also required to work on the installation of the ceiling base, which can be fabric or film. A feature of special tools is their high cost. Sometimes the equipment itself is more expensive than a stretch ceiling.

The selection and use of work tools requires a responsible approach:

• the variety of the list and functions of the models can confuse the user;
• the purchase of tools is carried out with the expectation of long-term use;
• the result and safety of work depends on the purchased devices.

To install stretch ceilings, you may need devices that you cannot do without. There is also a list of complementary tools. Highlight basic equipment and additional tools.

Power tools or gas systems can be used as equipment, and the use of hand tools is equally important.

The main technical means for tightening the entire system is considered to be a heat gun. It heats the material, which contributes to easy installation in the future. This technique operates on gas. It is more difficult to work on electricity for a gun, because when it is on, too much load is given to the electrical network. The heater body is made of steel with an enamel coating.

The interior of the gas-fired heat gun is equipped with a burner, air fan and steel grates. An open fire in the process of work heats up the room very quickly, so it is necessary to create additional free space near the device. The heating power level of the device is regulated using a special valve. In each specific case, it is necessary to use a specially designed gun of various sizes.

The main tasks for which the work of the heat gun is directed:

• an increase in the air temperature in the room;
• heating the entire surface of the stretch fabric;
• maintaining the required heat level during operation;
• prevention of fogging of the main floor.

Another important type of tool is a hammer drill, with which holes are made in the wall and ceiling, and the profile is installed. The set with the perforator must contain the drills required for mounting the baguette.

The screwdriver helps to screw in self-tapping screws. This tool can be powered by electricity and battery. It is more convenient to work with the latter option, since not all rooms are connected to the electrical network during the repair. The practicality of the workflow is ensured by using a smaller tool.

Other functions of the screwdriver:

• fixing the profile for fastening the canvas;
• installation of brackets for lamps;
• carries out other auxiliary operations.

To carry out the soldering of the tensioning system webs, they resort to the use of an HDTV machine. The seams formed as a result of the operation of this device are practically invisible, the ceiling looks like a continuous canvas. This is the value of the equipment in question. It bears this name because of the impact of high frequency current.

The product consists of two main parts: a welding press and a generator.

Additional accessories are room measuring devices and necessary parts for the ceiling:

• Ruler.

• The laser tape measure allows you to take measurements while standing in one place.

• The laser level is much more convenient for carrying out repairs, as it provides high accuracy of indications. For correct marking, the level is fixed by hand; it is also possible to mount it on the wall. This method involves setting the level on a stand, which is suspended on a self-tapping screw or fixed on the heating pipe. For uneven surfaces, a more convenient laser level mounting system has been developed. This is a tripod, which is placed with its supports in the floor and ceiling. A stand is mounted on the rod, which ensures the movement of the tool.

• Suspensions. Needed to hold the finished web. Their number depends on the size of the room.

• A cord for marking a room. The purchase of this part does not require a careful selection of a specific characteristic.

• Stable ladder with required height.

• Blades for fastening the profile. They are in the form of a spatula, which prepares the surface before directly stretching the canvas. Straight, curved and angled blades are suitable for work. The bending of the tool can have a different angle of inclination. A large and small shoulder blade stands out with a forty-five degree turn. The handle of the larger instrument is forty centimeters long.

A small spatula with the same angle is equipped with a handle no more than ten centimeters long.

The device, which has a structure curved like a ring at an angle of ninety degrees, is suitable for mounting hidden lighting in a box. There are scapulae in the shape of a triangle. Such models are capable of penetrating holes with uneven bases. A straight blade will come in handy for rooms in which water or gas pipes pass.

The repair also uses an electric spatula, which is a device with a moving blade. The cost of such a tool is much higher than a manual one, so it is not worth purchasing for one-time work.

Another list is highlighted, which includes materials important for self-assembly:

• drill;

• a gas cylinder with a volume of fifty liters, complete with a hose;

• sealant kit;

• glue;

• sharp stationery knife;

• Scotch;

• detergents that may come in handy during installation;

• plywood or plasterboard material may be needed if the installation of heavy lighting is planned;

• screwdriver crowns.

The part, without which the fastening of the stretch ceiling is impossible, is a profile. It is usually marketed with a length of more than two meters. The exact amount depends on the place of purchase. The profile is equipped with locks that have the function of fixing the ceiling base. Such a device greatly facilitates the installation, dismantling and adjustment of the ceiling during repairs. Many experienced craftsmen work with it.

Tools for installing stretch ceiling systems are selected taking into account the following points:

• production;
• the power level should ensure high-quality work performance;
• availability of a guarantee: the cost of most of the necessary devices is quite high, therefore, the period of warranty service allows you to save material resources in case the manufacturer turns out to be unscrupulous.

The choice of a heat gun depends on the area of ​​the room in which the stretch ceiling is being installed.For installing a ceiling in a small room up to 20 sq. m. it is enough to purchase a device with a power of 15 kW. It is easy to use due to its light weight. For larger rooms with high ceilings, a cannon with a power of at least 30 kW is needed for stretching.

The quality of a screwdriver depends on the durability of the battery. The longer the charge lasts, the better the device.

During the acquisition of an HDTV machine, attention is drawn to the presence of launch buttons. Better if there are two of them, they allow you to start the work process by simultaneously pressing both buttons at once.

High-quality equipment complies with safety regulations. In less traumatic devices, the unit can be started only with two hands.

When choosing a laser tape measure, attention is paid to a number of parameters:

• protection of the case from shock, moisture and dust;
• the presence of a stop for mounting the device in a corner: this is required to measure the room diagonally;
• to increase the accuracy of the size readings, the presence of a built-in level is encouraged;
• charging method;
• function of recording measurements in the device memory.

Experts highlight some important points that it is necessary to consider when choosing and working with tools and equipment for tensioning the ceiling with your own hands:

• The screwdriver used in the installation of tension structures must not have a rotating mechanism with an impact element. This leads to a rapid failure of such a device.
• The optimum radius of the laser level is at least 7 meters.
• When working with a gas cylinder, mandatory compliance with safety precautions is required.
• When purchasing a punch, you should pay attention to the well-known names of manufacturers, since they are more durable and capable of providing high-quality work.

• The hole drilling device is recommended for use with a built-in vacuum cleaner. This is important to reduce the amount of dust generated.
• Before installing the ceiling, it is recommended to purchase all possible types of blade shapes, since each option may be useful in a particular situation during work.
• For installation, it is better to work with a hammer drill with several operating modes. The functions of chiselling, hammering and conventional drilling are most necessary for the implementation of the installation process of the ceiling structure.

For an overview of the tool for installing stretch ceilings, see the following video.