Do-it-yourself tile cutter

A mechanical (manual) or electric tile cutter is a must-have tool for workers laying tile or tile coverings. Situations often arise when the whole fragment is a square, the rectangle is not tiled, because the distance is too small, and this difference cannot be cemented and "ironed" (or painted): the plan, the project of finishing the room will be violated.

Making a tile cutter from a grinder does not require special professionalism. Here, in addition to the grinder, the following components and tools will come in handy:

• metal plates 15 * 6 cm, with a wall thickness of 5 mm;
• steel ring with a strip 2 cm wide;
• textolite blank 30 * 20 cm, its thickness is on average 2.5 cm;
• bolts and nuts for a diameter (thread) of 1 cm;
• self-tapping screws;
• files and grinder;
• drill screwdriver (or drill and screwdriver separately);
• welding inverter and electrodes.

The goal is to recreate the rocker mechanics, where the angle grinder itself is fixed on one side. During work, the grinder is placed either closer or further to the cutting site, while making rotational-translational movements.

To make a "Bulgarian" tile cutter with his own hands, the master will follow a series of sequential steps.

• Cut the following blanks with a hacksaw or grinder: 3 - 40 * 45 mm, 1 - 40 * 100 mm, 1 - 40 * 80 mm and not yet quite the correct L-shaped part. The workpiece 40 * 45 is sharpened on one side like a semicircle - after the installation is completed, the corners do not interfere with the rotation of the rocker arm along the axis; a hole with a diameter of 1 cm is drilled at the central point. The workpiece 40 * 100 is the lower component of the rocker arm, it is attached to the PCB with the same 10 mm bolts. A workpiece 40 * 80 serves as the upper part of the swinging element. L-shaped - a lever, to the lengthening of which the grinder is fixed. The other end will connect to the center axis through an additional hole.
• Cut out a small area in the steel ring that fits over the support flange. Weld the nuts on the outside of the ring on both sides of the cut fragment - one per 10 mm. An M10 screw must pass through these nuts. By tightening this bolt, you will get a tightening clamp. It, in turn, is welded to one of the edges of the longer side of the L-shaped component.
• Screw the metal parts onto the center axle (M10 bolt). Pull them off with a nut and weld them so that the lever of the rocker arm with a clamp rotates around its axis. The rocker is attached to the piece of textolite through the holes in the lower component.
• Place the clamp on the support element of the angle grinder... Decide how it is most convenient for you to work with a grinder. Secure it with a clamp. Make sure that the cutting disc does not come into contact with the PCB base. Install a protective cover on top to prevent the scattering of debris and dust throughout the room, formed when cutting tiles or tiles. Grab it with a welded joint.
• Weld a hook or a piece of a corner with a hole on the top of the rocker arm mechanism... Hook a spring no more than 5 cm long onto it - this is exactly the length it will acquire in a compressed position. Pull it so that the underside of the cutting blade is raised above the PCB base.The second end of the spring will be in the hole in the corner, fixed with self-tapping screws on the piece of PCB.

A manual tile cutter is a worthy replacement for an electric one. He does not need exactly the same drive that is used in grinders. An example is a cut-off tool that cuts tile cells up to 1.2 m long. The sequence of actions during the procurement, finalization of parts and assembly of the device may be as follows.

• Checking the drawing, cut 4 fragments of a rectangular profile 5 * 3 cm... Purchase a steel angle, hairpin, bolts and bearing (roller, ball) kits.
• Make a guide based on 1.3 m pipe sections... Make sure you cut the pipe straight - there should be a different mark on each of the four sides.
• Sand the pipes on the side with the least rounding. This can be done using a grinder or a drill, on which the cleaning nozzle is attached. A roller (on the basis of wheels) carriage moves along the ground surface.
• The bed is manufactured as follows... Cut two of the same pipe pieces and grind it in the same way as the previous pieces. Place a strip of steel between them, which is a fracture element, and weld all these parts into a single whole. To prevent curvature, make a tack at the ends, then point-weld this guide along its entire length.
• Attach the bed to the guides. To do this, weld the studs along a piece to the bed from the ends. The guide rail is formed by joining two pipes together to form a 4.5 mm gap. Then weld the nuts to the guide. Drill out the threads in them - it is not needed. An alternative is steel plates with holes drilled into them. Assemble the structure so that there is another one between the nuts, but with a thread, the level of the slide is set along it. Install the lock nut - the slide is fixed with its help most reliably.
• Make a carriage out of 4mm stainless steel sheet. A cutting roller is attached to it. The carriage moves along bearings mounted on an intermediate sleeve made of simple nuts, from which the outer edges are removed (turnkey). To turn the nuts evenly, use a clamped drill with a bolt in the chuck - the nut is screwed onto it. This method allows you to do without a lathe - a drill and a grinder will replace it.
• Assemble the guide, having prepared a moving part for it, consisting of a bolt, a bushing, a bearing roller, a pair of adapter nuts clamping the carriage element, another bushing, another bearing and another nut.
• Cut the component out of a piece of stainless steel sheet... Weld a nut to it. Cut holes for the moving parts on the underside.
• Attach the cutting roller to the bearing cage between the two brackets... Tighten all other parts with nuts and bolts.
• Install the cut roller on the carriage mechanism.
• Fasten the spacer accessoryNS. She breaks the previously sawn tiles.
• Make and secure the handle - for example, made from a piece of polypropylene pipe. Place pieces of cured foam glue - the bed will be softened, the movements will become less abrupt. Place the locking element on the carriage mechanism - it will be located above the rails, this will prevent the carriage from suddenly "moving" up or down along the rail. Install bearing kits at the top - they will make the movement of the saw smoother.

The homemade tile cutter is ready. It is durable, its disadvantage is increased weight.

Stick to the following rules.

• Cut the tiles without moving the tool towards you.
• Avoid unnecessary pressure.
• Start sawing from the front, not the wrong side.
• Fix the tile square with tongs or clamps - it is lightweight.
• If there is no experience, then first practice on scraps, old fragments of removed tiles, large fragments of tiles.
• Do not cut tiles or tiles without marking.
• Use safety glasses. Dry cut will require a respirator.
• Keep the tile cutter out of the reach of children.
• Do not start work without making sure that the cutting blade is not worn out.
• For wet cutting - before cutting - wet the surface. Stop the drive periodically to re-wet the cut site. A wet cut prolongs the life of the cutting blade, preventing it from overheating.

For how easy it is to make a DIY tile cutter, see the next video.