All About Foam Sizes

When building a house, each person thinks about its strength and heat resistance. There is no shortage of building materials in the modern world. The most famous insulation is polystyrene. It is easy to use and is considered quite inexpensive. However, the question of the size of the foam should be considered in more detail.

Let's say you are starting to insulate a house and want to use foam for this. Then immediately you will have a question, how many sheets of polystyrene you need to purchase so that it is enough for the geometric dimensions of the insulation area. To answer the question posed, you will need to find out the dimensions of the sheets, and only then carry out the correct calculations.

Foamed polystyrene foam insulation is made on the basis of GOST standards, which require the release of sheets of certain sizes. After you know the exact numbers, namely: the dimensions of the foam sheets, you can easily carry out the calculations. For example, if you are going to insulate the facade, then you will need units of rather large sizes. If you have limited space, then use shorter units.

If you know the dimensions of the purchased foam sheets, then you can also answer additional and very important questions.

• Can you handle the job yourself or do you need an assistant?
• What kind of car should you order to transport the purchased goods?
• How much fastening material do you need?

Standard foam boards vary in size and thickness. Depending on the purpose, their maximum thickness and length may vary. Some units are 20mm and 50mm thick. Please note that if you want to insulate the walls of the house from the inside, then foam of just this thickness will do. And it must also be added that the thermal conductivity of a sheet of this thickness is also quite high. It should be understood that foam sheets are not always standard sizes. Their width and length can range from 1000 mm to 2000 mm. Depending on the wishes of consumers, manufacturers may well produce and sell non-standard products.

Therefore, on specialized databases, you can often find sheets that have the following dimensions: 500x500; 1000x500 and 1000x1000 mm. In retail outlets that work directly with manufacturers, you can order foam units of the following non-standard sizes: 900x500 or 1200x600 mm. The thing is that according to GOST, the manufacturer has the right to cut products, the size of which can fluctuate in the plus or minus direction by about 10 mm. If the board has a thickness of 50 mm, then the manufacturer can reduce or increase this thickness by 2 mm.

If you want to use styrofoam for finishing, then you need to buy the most durable units. It all depends on the thickness. It can be either 20 mm or 500 mm. The thickness multiplicity is always 0.1 cm. However, manufacturers produce products that have a multiplicity of 5 mm. The material to be finished must be very dense. Therefore, you should choose products based on the brand indicators, they can be 15, 25 and 35 units.For example, a sheet having a thickness of 500 mm and a density equal to 35 units may well be analogous to a sheet that has a thickness of 100 mm and a density equal to 25 units.

Consider what kind of foam sheets manufacturers often offer.

• PPS 10 (PPS 10u, PPS12). Such products are mounted on walls and are used to insulate the walls of houses, change houses, combined roofs and others. This species should not be exposed to loads, for example, to stand on them.
• PPS 14 (15, 13, 17 or 16f) are considered the most popular. They are used to insulate walls, floors and roofs.
• PPP 20 (25 or 30) used for multilayer panels, driveways, car parks. And also this material does not allow the soil to freeze. Therefore, it is also used in the arrangement of swimming pools, foundations, basements and much more.
• PPS 30 or PPS 40 it is used when floors are arranged in refrigerators, in garages. And also it is used where swampy or moving soils are observed.
• PPP 10 has very good performance. This material is durable and strong. The dimensions of the slab are 1000x2000x100 mm.
• PSB - C 15. Has dimensions 1000x2000 mm. It is used for insulation in the construction of industrial facilities and for the arrangement of facades.

Need to Know: The listed instances do not represent a complete list of models. The standard length of the foam sheet can be either 100 cm or 200 cm. The foam sheets are 100 cm wide, and their thickness can be 2, 3 or 5 cm.The temperature that the foam can withstand can range from -60 to + 80 degrees. Quality foam has been in service for over 70 years.

Polyfoam is a versatile insulation. With the help of such material, you can create a certain microclimate in the room. However, before installing the foam sheets, you will need to calculate the amount of material used and its quality characteristics.

• All calculations must be carried out based on different guideline numbers and different requirements.
• It is imperative to take into account the structure of the building itself in the calculations.
• When making calculations, be sure to take into account the thickness of the sheets, as well as their service life.
• It is necessary to take into account both the density of the material and its thermal conductivity.
• Do not forget about the load on the frame. If your structure is fragile, then it is better to use lighter and thinner sheets.
• Insulation that is too thick or too thin can result in a dew point. If you calculate the density incorrectly, then condensation will accumulate on the wall or under the roof. This phenomenon will lead to the appearance of rot and mold.
• In addition, you need to consider the decoration of the house or wall. If you have plaster on your walls, which is also a good insulation, then you can buy thinner sheets of foam.

For the convenience of the calculation, you can use the following data. They were taken from a common source. So: calculation of PSB foam for walls: p (psb-25) = R (psb-25) * k (psb-25) = 2.07 * 0.035 = 0.072 m. Coefficient k = 0.035 is a fixed value. The calculation of the heat insulator for a brick wall made of PSB 25 foam is 0.072 m, or 72 mm.

Polyfoam is an insulating material that will help solve many problems. However, before proceeding with the installation of foam sheets, you need to decide on the amount of purchased goods. If you calculate the material consumption correctly, you can avoid unnecessary waste. Before making an estimate, find out what sizes the products are. It's easy to choose the right product. You just need to know the width, length and thickness of the sheets.Standard sheet white foam is suitable for insulating absolutely all rooms. For the calculation, some professionals use special computer programs. In order to calculate the correct consumable, it is enough to enter the following data into a special table: the height of the ceilings and the width of the walls. Thus, the length and width of the foam sheets are selected.

The easiest way, however, is to take a tape measure, a piece of paper, and a pencil. First, measure the object to be insulated with foam. Then take up the drawing work, with the help of which you can determine the number of sheets and determine their dimensions. The area of ​​the foam sheet greatly affects the ease of installation. Standard sheet sizes fit in half a meter. Therefore, you should calculate the surface area. Then calculate how many standard sheets can be laid on this surface. For example, on the floor on the ground (under the warm floor), calculations are quite easy to carry out. It is enough to measure the length and width of the room, and only then decide on the dimensions of the foam plates. Another example: to insulate a frame house from the outside, it is better to use larger slabs. They can be ordered directly from the manufacturer. In this case, lining with insulation will take you not so much time. Plus, you will save on fasteners. It is much more profitable to buy large slabs for the following reasons: installation times are significantly reduced, and you do not need to purchase additional mounting units.

However, in this case, you run the risk of facing some inconveniences. If you carry out internal insulation of the house, then you will need to first bring all the volumetric foam units into the house. This is a rather difficult task. In addition, a very large sheet can easily break. To avoid such a nuisance, two people will have to carry it.

However, some consumers prefer to buy custom-made foam sheets. Manufacturers are happy to make concessions to customers and supply goods that differ in non-standard sizes. In this case, the purchase price increases significantly. However, you make it easier for yourself.

The following information will help you determine the size.

• It is easier for one person to work with oversized slabs. Therefore, if you rely only on yourself, then consider this point.
• If you are going to lay the insulation to a greater height, then it is better to buy sheets of smaller sizes. Large sheets are very difficult to lift up.
• Consider the conditions for laying insulation. For outdoor work, it is more convenient to buy sheets of large sizes.
• Slabs of standard sizes (50 cm) are fairly easy to cut. The leftover pieces can be useful for working on slopes and corners.
• The best option for wall insulation will be a sheet of foam plastic 1 meter by 1 meter.