How to paint OSB plates outside the house?

In recent years, OSB materials are increasingly used for exterior decoration of private houses. Therefore, the question of their coloring is especially relevant today. In our review, we will consider all the subtleties of choosing facade dyes for buildings sheathed with OSB panels.

In order to correctly select a dye for OSB sheets, you should understand the features of this material. OSB is a tough wood fiber shavings mixed with resins and compressed under high pressure and heat.

The main components of such dyes are alkyd resins. They are produced by boiling a mixture based on vegetable oils and mildly corrosive acids. After being applied to OSB sheets, this enamel forms a thin and even film, which, during operation, protects the surface from adverse external influences, including moisture infiltration. Alkyd paints have a low price, while the material is resistant to UV radiation and low temperatures. The enamel dries in just 8-12 hours, it is absolutely safe, although the drying of the dye is often accompanied by the appearance of an unpleasant odor.

The use of alkyd compounds requires thorough preparation of the treated surface. If this step is neglected, the paint will peel and bubble.

In recent years, oil dyes have been used infrequently, since a large selection of more practical formulations has appeared in the modern construction segment. Oil paints are highly toxic, any work with them should be carried out using personal protective equipment - a mask or respirator. At the same time, they are not cheap, since they are made from expensive raw materials. For the final drying of the paint, it takes at least 20 hours, during this time drips very often appear. Oil compositions are characterized by low resistance to adverse weather conditions, therefore, when used, the dye layer on the facade often cracks.

Acrylic paintwork materials are made on the basis of water and acrylates, which act as binders. After applying enamels to the surface of the OSB sheet, the water evaporates, and the remaining particles form a dense polymer layer.

Latex paints are one of the types of water-based compositions, the binder in them is rubber. The price of this material is much higher than all others, nevertheless, all costs are fully paid off by the increased performance characteristics of the product and the exceptional quality of the coating. Latex paint is distinguished by its elasticity, it does not deform even when the plate itself is destroyed. This dye is not afraid of mechanical stress. The wear-resistant coating insulates the OSB sheets 100% from moisture and thus ensures the required degree of sealing. The painted surface becomes resistant to atmospheric factors.

It is important that latex dyes are characterized by increased environmental friendliness. During use, they do not emit harmful volatile compounds and do not give a chemical odor when applied. The bonus will be the ease of cleaning the coating - you can get rid of dirt with the simplest detergents.

Water-based paint is rarely used for coloring OSB sheets. This is due to the fact that the material swells under the influence of external factors. If the OSB sheet is painted on only one side, then this leads to its bending. Therefore, the processing of such plates with water-based means can be performed only when the finish type of finishing will not have a special role.

Painting is a relatively budgetary way that will help give OSB panels a neat look and visual appeal. Most developers love the woody texture they want to accentuate. In this case, the best solution would be to purchase transparent enamels with a UV filter - and the best reviews were awarded Cetol Filter products... It is an alkyd enamel used for the exterior cladding of wood. The coating is characterized by transparency and light semi-matt sheen. The dye contains hydrogenators, as well as UV stabilizers, their complex effect provides maximum protection of the tree from the adverse effects of atmospheric factors.

If it is necessary to preserve the chipboard texture of the boards, you can take transparent glazes - they emphasize the woody pattern, but at the same time give the surface the desired color. The widest selection of glazes is offered by Belinka.

Transparent varnishes for wood give the OSB surface a glossy look. It is best to take LCI on a water, organic or oil base. Wood acrylic lacquer protects the structure of the material, while yacht lacquer gives it a decorative touch. The most practical choice will be the semi-matte composition "Drevolak". It is evenly distributed over the OSB and fills in all the unevenness of the coating.

To mask the woody structure and form a flat surface, preference it is better to give it to Latek and Soppka products.

When choosing a colorant for cladding from OSB panels, it is important that the selected material meets certain requirements.

• It was suitable for outdoor use. Accordingly, the material must be resistant to water (rain, snow), temperature fluctuations, ultraviolet radiation.

• Protected wood fibers from infection with pathogenic microflora - fungi and mold. Alas, not all varieties of OSB are factory-impregnated with antiseptics, so the paintwork should provide all the necessary protection.

• Prevented combustion. The dye must be resistant to fading and spread of fire, and must also contain a set of flame retardant additives.

• As far as the facade of a building is concerned, it is important that the paint has exceptional decorative properties. It is desirable that the user has the ability to shade the selected material in the color that is suitable for the implementation of the design concept.

Unfortunately, most builders neglect these rules when erecting buildings and use cheap substitutes - traditional alkyd enamels, conventional water emulsions and standard oil paints. At the same time, they completely do not take into account the fact that OSB is a composite material. It is made with the addition of adhesive binders, usually natural or formaldehyde resins, as well as waxes, act in this capacity.

That is why the use of dyes that have successfully shown themselves when toning an ordinary board does not always lead to the desired effect on the slab. Due to this preference should be given immediately to compositions made specifically for OSB sheets - this will allow you to significantly save your time, money and nerves.

The paint is selected depending on the expected result. So, when using pigmented paintwork materials, the wood texture of the OSB panel is completely painted over, and a dense monotonous coating is obtained. When applying colorless compositions, it is assumed that the expressiveness of the wood texture of the board will increase.

If you are carrying out budget finishing outside the building, then you can ignore these minor flaws. However, if the requirements for finishing work are high, then you should adhere to a certain sequence of steps when tinting the slab:

• application of primer;

• fixing fiberglass mesh over the entire surface of the slabs;

• puttying with a hydro-resistant and cold-resistant mixture;

• finishing staining.

If you are going to use elastic dyes, then the puttying step can be skipped. Such paints fit well on fiberglass and mask it; after applying the next layer of enamel, the plate acquires a glossy surface.

In order to achieve the most uniform application of the composition, master finishers are advised to paint in a certain way.

It is better to paint the perimeter of the panel in 2-3 layers, and then use a roller to gently redistribute the dye over the entire surface of the slab.

The rest of the panel is painted with as thin a layer as possible, the coating is applied in one direction.

Before painting the next layer, let the coating grasp and dry. It is advisable to carry out all work in warm dry weather in order to exclude sudden changes in temperature, drafts and the effect of atmospheric precipitation. The approximate drying time for one layer is 7-9 hours.

The dye is applied using different techniques.

• Spray gun. This method is used to create a strong, even coating. Such staining is done quite quickly, but this significantly increases the consumption of enamel. Plus, the device itself is expensive. You can resort to this method only in calm dry weather with the obligatory wearing of a respirator.

• Brushes. The most common option, gives a durable, high quality coating. However, it takes a lot of time and is very laborious.

• Rollers. Such coloring can significantly speed up the process of applying the dye. With such a tool, large areas of OSB panels can be updated quickly and efficiently.

If you wish, you can use unconventional ways to paint the walls. For example, imitation of stone masonry looks beautiful. This technology requires a lot of time, since it involves multi-stage staining.

• First you need to print or draw an image with the design that you plan to reproduce. You should not choose overly intricate textures.

• Next, determine how many shades you need, and paint the panels in a base shade paint - this should be the lightest shade.In this case, the surface does not need to be sanded, and in order for the dye to be distributed over the uneven coating as evenly as possible, it is advisable to use a spray gun.

• After drying the paintwork, the surface is slightly protected. In this way, the relief and depth of the texture are emphasized.

• Then, with an ordinary pencil, the contour of the masonry is transferred to the surface of the panel, and then it is emphasized in a dark tone using a thin brush.

• After that, it remains only to cover individual stones with colors of other shades to create the effect of volume.

• The result obtained is fixed with varnish, it must first dry thoroughly.

The second interesting way is toning with a plastering effect. This is a simple technique that does not require any artistic talent from the master.

• First you need to sand the slab to remove the wax coating.

• Then a primer is performed, and the base color is worn. He is selected, focusing exclusively on individual preferences.

• After the soil has dried, the surface is slightly sanded. This should be done using fine-grained emery.

• After removing the remaining dust from the panel, apply a dye with a patina or mother-of-pearl effect. You can use both formulations at once, but in turn. After applying the enamel, you should wait 10-15 minutes, and then walk on the painted surface with emery.

• The result obtained is fixed with varnish.

Using facade dyes for finishing oriented strand surface, you should be aware of the individual intricacies of performing such work.

• All sharp corners of the sheets often cause cracks in the applied coating. Therefore, any work must begin with the obligatory grinding of these zones.

• The edges of the slabs are characterized by increased porosity. These areas require preliminary sealing.

• To improve adhesion and reduce water absorption characteristics, the panels must be primed first.

• The process of tinting OBS boards on the street requires a multi-layer application of paintwork materials, therefore each layer should be made as thin as possible.

• If the surface of the sheet is rough, the consumption of enamel will be increased many times over.

If the material has been in the open air for more than a year, then before processing it must be thoroughly cleaned of all dirt, dust, treated with fungicides and sanded.