How to cut tiles with a grinder: important nuances of the process

In the process of laying tiles, it becomes necessary to trim it so as not to touch pipes, counters, or put a piece smaller than the standard size. A tile cutter will do the job better, but in some cases only a grinder can do it. Although it often performs the function of grinding, it also copes perfectly with other tasks.

Cutting a tiled surface with a grinder can be carried out without dust, chips that can damage the surface. To understand how to cut the material, no special knowledge is required, you just need to accurately fix the tile.

For direct work, you will need the following materials:

• using a marker, marks are made for future cutting;
• a ruler on which the marks are fixed;
• protection in the form of glasses;
• Bulgarian.

It is important to check several times whether the measurements are correct.

The steps in the process are as follows:

• first, the cut line is evenly applied with a marker along the ruler;
• fix the tile material on a stable base;
• then you need to turn on the grinder, wait a few seconds and hold along the mark away from you.

It is important to consider what kind of material you want to cut. If you have to deal with a ceramic coating, then the whole process takes place on the surface, where one edge of the material hangs down.

It is important to cut the tile base not to the very end, but only to reach half the thickness. Then the tile is placed on the table, the edge of which must match the edge of the tile.

To cut ceramics, you need special discs that are designed specifically for this. Most often, there is an inscription on the circle itself indicating the direction of the turn. The quality always depends on the price. There are the following types of discs:

• Stone rarely used due to their quick ability to grind and spread dust. During the cutting process, you need to control the cutting base. If there are irregularities on the edge, replace the disc to avoid damage.

• Metal diamond circles. In turn, they are divided into solid and divided into compartments. For ceramics, the first type is better. You cannot work with such a nozzle for more than one minute. Take short breaks to cool the instrument. Segment discs are suitable for porcelain stoneware, concrete or stone. This type of attachment has correctly positioned slots that are designed to increase service life.
• Special wheels for wet cutting allow you to cut the tiles without dust by the ingress of water to the nozzle.

If you need to cut a brick of paving slabs, then only a diamond wheel will help in this situation.

Here are some things to remember:

• use not only safety glasses, but also headphones due to the increased noise level;
• the grinder must have a lot of power to cope with the material;
• avoid dust ingress on the already tiled surface.

To operate the tool without the formation of a large amount of dust and debris, you need to know all possible methods, depending on the direction.

Three cutting techniques are distinguished:

• Straight. To do this, the tiles must be firmly anchored to a stable surface. It is important to see in which direction the grinder is moving. The best speed for a circle with a diameter of 100 millimeters is equal to 8000 rotations per minute.
• Angle 45 degrees. To get an uneven cut, the tile is first cut at a ninety degree angle. Using a metal diamond disc, the tool should be guided towards the removal of unnecessary material. You can make the edges perfect by scraping with paper with a special base.

• To create a large hole. Preliminarily, on the front side of the slab base, the contour of the circle is determined with a writing instrument. Then its center is established using perpendicular intersecting lines. During cutting with a grinder, the disc rotates in such a way as to deepen along the inside of the marked line. The material is cut slowly and evenly over the sectors of the circle.

To prevent injury during the work process with the participation of the grinder, you must adhere to the list of rules.

Basic safety requirements:

• Before starting work, it is recommended to check the rotational ability of the disc.
• Check the sharpness of the tip. If the wheel is blunt, it must be replaced immediately, otherwise the tool may be destroyed.
• Even with short-term use of the grinder, you should not neglect equipping the face and body with special protection. This is especially true for eye safety, so you should always wear glasses.

• During the cutting process, if possible, avoid simultaneous contact with other people, since being distracted, there is a great risk of injuring your hands.
• Do not start cutting the tile surface immediately. You need to wait for the full speed of spinning the circle.
• The disc in work should be directed in the direction opposite to the person performing the cut.
• Do not allow the wire to be pulled, so you need to control the distance. It should be no more than half a meter.
• It should be remembered that with the correct installation of the tool, it is able to make the cut itself. Therefore, strong pressure on the cutting device is avoided.

When sawing different types of tiled bases, it is recommended to adhere to several useful tips:

• If possible, work only with new discs that differ in their sharpness.
• When cutting tile materials, only the average revolution is used, the lower and maximum ones are excluded.
• The disc is attached to the grinder only with a specially designed key.

• When choosing a cutting tool, you should pay attention to the possibility of adjusting the speed, since depending on the surfaces to be cut, a different number of revolutions can be used.
• When cutting paving slabs to reduce the spread of dust, experts advise to moisten the tile surface abundantly with water and connect a vacuum cleaner to the grinder.
• In addition, a special cap, which is attached to the cutting device, will protect against the spread of fragments.

In general, the reviews about the effectiveness of cutting tiles with a grinder are positive. This method saves money as it does not require the purchase of a special tile cutter. In addition, the tool can handle fairly complex materials intended for both wall cladding and flooring. A good grinder for tiled surfaces of different styles, from loft to classic.

Consumers also note that this is a fairly traumatic tool that requires care and attention.

According to those who have already tried to cut in this way, a high-quality result is always ensured by carrying out a trial cut of any rough piece.

For information on how to cut tiles with a grinder, see the next video.