The process of making an electric barbecue

May weekends, a trip to the country or nature are often associated with barbecue. To prepare them, you need a brazier. But often it will be expensive to buy a finished product in a store. The solution to this issue will be a self-made electrical apparatus. What materials and tools will need to be used is described in this article.

Depending on the design and the possibility of movement, they are distinguished:

• stationary;

• portable barbecues.

The first type is brick or massive metal structures., the bases of which are recessed into the ground or the floor of the gazebo. If the brazier is installed under a canopy, cooking becomes possible even in bad weather. The latter have mobility - they can be moved to another place, taken with you to a picnic. They are easy to cleanse. But at the same time, due to the small thickness of the metal, the service life of such structures is short, in contrast to the previous version.

According to the type of fuel, there are gas, electric models or coal-fired products. Each type has its own advantages. Barbecue experts believe that using an electric motor only harms the end result, and the meat is not as good as when using a regular wood-fired brazier. There is some truth in this, but the preparation of products in this case will be long.

The gas model is also good in its own way, but at the same time you need to constantly take a gas cylinder with you. This is pretty insecure. When using an electric shashlik maker, time saving is a positive point. Due to the electric rotation of the skewers, the meat is juicy and moderately fried. Also, in this case, the fat will not drip onto the coals, respectively, the pieces of meat will not burn. There is no need to closely monitor the process as it is automated.

If you correctly assemble your home electronic grill, then the result will be no worse than using the store option.

To make a classic model of a kebab maker, you will need:

• 4 plates made of 4mm steel;

• metal corners;

• fasteners;

• electric drill;

• welding machine;

• LBM (angle grinder).

You start by making the walls. Cut 2 pairs of strips 35 cm high with a grinder. Longitudinal (long side) and transverse (short end) sides are obtained. Choose the length of the product based on personal preference, but remember that, on average, from 6 to 10 skewers should be placed on the structure at the same time. It is recommended that you first draw up a drawing on paper, and only then implement the project idea. The bottom of the kebab maker is prepared last.

For a skewer, you need to drill a hole with a diameter of 1.5 cm in one of the side parts. In the bottom plate, also make 2 rows of holes in a checkerboard pattern. Using corners, fasten the sides, and for greater tightness, the bottom and sides must be welded. Next, from a corner measuring 25 by 25 centimeters or a metal pipe with a caliber of 30 cm, make legs from 60 to 110 cm long and attach them to the body using fasteners.

It is recommended to make a stand from a pipe, because this way it will be easier to mount and dismantle the brazier every time when the need arises. After all the stages, the structure must be covered with a special paint for metal. This way it will last longer and be less corroded.

The paint material must be heat resistant.

Here are some suitable paints:

• Certa is able to withstand temperatures of + 900C. It may have the name OS-82-03T.
• Rust-oleum - up to + 1093C. Matt black, white or silver color.
• KO-8101 - up to + 650C. The palette contains 12 colors.
• KO-8111 withstands thermometer readings up to + 600C.

It is not necessary to make a brazier from solid metal sheets. It can be made using several pieces of metal welded together, or you can use an old metal barrel. From it you can make either one barbecue with a lid, or two separate braziers. After that, you should decorate the structure with unusual elements or just paint it.

If you follow the advice of professionals, it is better to use a heat-resistant material. This will prevent deformation of the structure. Indeed, during the cooking process, the structure is exposed to high temperatures.

Cast iron is considered another high-strength, durable and heat-retaining element. But, as a rule, finished products from it are heavy, and it will be difficult to transport them. But for creating a stationary barbecue, this option may well be suitable.

There is a lot of controversy over galvanized steel. When heated, the material can emit harmful substances into the atmosphere, and according to some masters, during cooking, they can get into the meat. However, most users tend to consider this a delusion, because the material cannot be heated to such an extent that zinc begins to be released.

The most widely used option is stainless steel. Such products are not subject to corrosion and can be left outdoors even in rainy weather. The material is distinguished by its durability - the duration of their service is several decades. From an aesthetic point of view, the design will blend harmoniously with any landscape.

The choice is made based on personal preference. Or the materials that are currently available are used.

As a motor, you can use a window washer motor or a motor that drives the wipers. The side of rotation is irrelevant. The voltage should be 12 volts. If it is higher, then the rotational speed will be correspondingly higher, and the meat will not be cooked to the required degree.

The structure will cease to be mobile, and there is a risk of electric shock. Depending on the motor model, it can be powered by electricity or a battery.

In order for the skewers to rotate, in addition to the engine, you will need gears, chains, and a source of electricity. Install a pulley or main sprocket of a metal belt to the motor shaft. They must be different in size, due to this, the rotational speed will be reduced. The engine is connected from below to the kebab maker.

In order for the electric motor to function correctly, it is necessary to assemble the gears into a single system, the assembly algorithm of which looks like this:

• Attach one gear, then attach a chain to the motor housing.
• Next, attach another gear to the wall of the electric gun.
• Reattach the remaining gears in sequence.

After all the manipulations, you can check the performance of the resulting kebab maker. When you turn on the device, the 1st gear starts. Then the moment is transmitted to the next gears. As a result, the skewers rotate at the same speed. To adjust the degree of their rotation, you need to tighten the belt.

These tools are designed for different purposes. The skewer is used for preparing large pieces of meat or poultry, and skewers for small pieces. The length of the spit should be 15 cm more than the width of the electric barbecue so that nothing interferes with the rotation of the tool. The optimum thickness is 15 mm. The width of the rod is chosen depending on the pieces of meat that you plan to cook.

The skewer can be flat, round, square or in the form of a corner. For the smallest pieces of meat, a flat shape is suitable. Thanks to the square, you can conveniently cook minced meat dishes; due to the special design, the product will not slide off. The round version is not convenient, because during cooking the meat turns over and slides off the skewer. The tool must be strong, otherwise, when turning over, the pieces may fall into the brazier.

Skewers can be purchased at the store or made by yourself.

This requires the following materials:

• hammer;
• pliers;
• chisel;
• steel bar;
• forging tools for metal processing;
• emery machine.

First, from a rod with a caliber of six mm, using a chisel and a hammer, you need to make 6-10 segments 70 cm long. For the convenience of working with metal, it is better to preheat it in an oven or in a lighted fire. Then you need to wait a little until the material cools down, otherwise it will break easily, and everything will have to be done again. After the material has cooled down a little, you need to give the future skewer a certain shape with a hammer and an anvil. The thickness should be within 2.5 mm, 10 cm should be stepped back from the opposite side.

This part will be a handle, it should be bent in the form of a circle or in the form of a spiral with the help of pliers. Next, the machine needs to process the main part of the skewer, the end needs to be slightly sharpened. After that, you lower the finished product first into a fire source, then immediately into cold water.

All stages of preparation have been completed. You can start testing the resulting electric kebab maker and homemade skewers and skewers.

Based on all of the above information, certain conclusions can be drawn.

• You don't need a lot of skills and dexterity to make an electric gun yourself. Everything is simple enough. The main thing is to first create a plan on paper, and only then bring it to life.
• It is not necessary to use solid metal on the brazier, you can use separate parts and weld them together, or find a use for an old metal barrel. The best option is stainless steel. The products are not subject to corrosion and can be left outdoors even in rainy weather. The material is distinguished by its durability - its service life is several decades. From an aesthetic point of view, the design will blend harmoniously with any landscape.
• If you do not want to design a brazier for a long time, you can purchase a ready-made and independently connect an electric motor.

• As a motor, a window washer motor or a motor that drives the wipers is suitable. The side of rotation is irrelevant. The voltage should be 12 volts. Depending on the model of the motor, it can be powered by electricity or a battery.
• If there are no skewers and skewers, no problem. You can make them yourself from available tools.
• Electric bangles and grills for enclosed spaces are not used at home.

Self-production of an electric link does not take much time, and the end result will be delightful all the time. After all, you no longer need to closely observe the process of cooking meat. Only occasionally, to make sure that the mechanism is working properly, can a check be carried out. If you no longer need an engine and want to fry the meat pieces in the usual way - on coals, then this is possible. The electrical part can always be dismantled and reinstalled when the need arises.

For information on how to make a brazier with an electric drive with your own hands, see the next video.