How to install a hammock at home and outdoors?

Most people think that a hammock can be used for relaxation only in natural conditions, but this opinion is erroneous. On the one hand, a similar object was invented in order to hang it between trees, however, it is also quite appropriate in a room. A person, without leaving his home, at a convenient time for himself, can sit in a hammock and enjoy a lulling swing. But before you have fun the hammock must be properly hung.

To hang a hammock with your own hands, certain requirements must be followed.

1. The ceilings in the room must be at least 2 m.To perform inverted positions, the ceilings must be at least 2 m 20 cm.
2. In order to fix the hammock correctly, it should be remembered that the size between the fasteners is calculated depending on the height of the ceiling: up to 3 m - 0.6 m; 3.5 m - 0.7 m; 3.5 - 0.8 m.
3. The necessary indents from the walls should be observed: in front and behind the product - 150 cm, on both sides of it - 100 cm.
4. In the absence of certain skills, it is better if the fasteners are installed by a specialist.

To start it is necessary to determine the placewhere you can relax in a hammock. It is permissible to install a hammock on a balcony, on a loggia or in a room. Here you should take into account what the subject will be needed for. For example, some people buy a hammock for comfortable watching movies and reading, others just want to admire the scenery outside the window.

Similar product can be hung between opposite and between adjacent walls... Here you need to take into account the fact that the walls must be capital. The most suitable will be brick or concrete walls, and the following are selected for fasteners: anchor bolts, plates for fasteners, products with an eyelet.

In some cases, the distance between two fasteners can be shorter than the entire size of the product. But it is better if this distance is greater, then there is a chance to adjust the position of the product using the ropes.

Fasteners are the most important thing when hanging a product. Based on the type of house and floor slabs, ordinary anchors can be usedwhich are well suited for solid slabs, or their folding types, characterized by the presence of auxiliary elements, which are represented by folding parts. The latter are suitable for hollow core slabs.

To hang the product from the ceiling, you can use ordinary ropes, but in some cases, chains will come in handy. Especially when a wide variety of hammock is installed. In addition to the anchor bolts, it is possible to make circular metal plate ceiling mount with hook.

When calculating the height, the following rules should be taken into account.

1. The fastening height is calculated according to the distance between the fastening points. The distance between the fasteners must be twice the height.
2. When the place on the wall where the fastening is supposed to be made belongs to the passage area, then, for special safety, it is better to make the fasteners higher than the height of the tallest person living in the apartment.
3. It is optimal when the fasteners are located at a distance not exceeding the level of an outstretched arm, so that the product can be suspended and removed without spending a lot of time.
4. When the distance between the fasteners is quite large (up to 6 m) and it is necessary that the product is placed not in the middle, but slightly towards the wall, then in order to align the position of the hammock, it is recommended to place the most distant support higher than the nearest one.

Thus, we can conclude that it is better to install fasteners at a height of 1 m 80 cm from the floor surface... If the distance between the fasteners is 300-350 cm, then they can be fixed somewhat lower, stepping back 1 m 50 cm from the floor.

If you intend to install a hammock with slats, then the mounts can be positioned slightly lower than recommended. Besides, it is better to choose the smallest size of ropes, which will not allow the product to sag, and it will be taut.

The height of the fasteners depends on the distance from the floor... Practice shows that it is better to relax in a hammock stretched higher than in one that is located close to the floor surface. A win-win variation is the formation of 2 loops on all ropes so that it becomes possible to hang the hammock in 2 positions: the safest position (when it is possible to put your feet on the floor) and the traditional one (when the product is higher).

Before installation, it is worth visually determining the convenience of the location of the product... It is not so easy to do it alone, you need a partner. You need to take the hammock with the ropes attached to it and attach their edges to the intended areas of the fastening, then adjust the ropes to the desired size. Check if any piece of furniture will interfere with the easy rocking of the hammock and if there is a support from which to push off.

Once the location and height are chosen, you can start installing the fasteners. An uncomplicated, budgetary and safe way is to use anchor bolts... For such a case, you can use a rounded or hooked anchor bolt with a width of 1 cm and a length of 6-8 cm. When installing in a plastered brick wall, auxiliary washers will be required.

In planned locations holes should be made, a drill is used for this. If you follow the advice, then first you need to make a hole with the smallest diameter (for example, 0.6 cm), then increase it to 1 cm. Remove debris from the resulting hole, insert anchor and, while holding the tip of the anchor, tighten the nut completely. That's all left hang a hammock.

If at home the distance between the supports exceeds the size of the product, then auxiliary ropes are needed for reliability. There are several ways to place your hammock on these legs. It is recommended to make a knot at the ends of the rope. Then push the free end of the rope into the loop of the hammock and the eyelet of the resulting knot. The same steps are required for the other rope. This way, all the ropes will be attached to the product. The last step is to attach the ends of the rope to the anchor. When the latter is a hook, then just the knots on the rope will be enough, and if the mount comes with an eyelet, then carabiners will still be needed.

Having finally decided on the number of nodes, you should start forming them. It is recommended to use the figure eight knot when hanging the hammock. After it is formed, it is attached to the fastener.

To hang a hammock on a tree, do not overlook the place under it.From this area, stones, branches and any elements should be removed from which injury could be caused if the hammock overturns and the person falls.

After the place is determined and cleared, you should proceed to the installation. There are many ways to hang a hammock from trees, but we will look at two of the easiest and most convenient ones. First you need to attach ropes to the product. A knot is formed on one side of the ropes, a figure-of-eight knot is recommended. Now the end of the rope, where there is no knot, is pushed into the ear of the hammock and the loop of the knot of the other end of the rope. This will secure it at all ends of the hammock.

The rope is now attached to the tree. This can be done in two ways. The first does not provide for the use of a carbine. This is the case when the free end of the rope is fixed to the tree. But in the second method, carbines will be needed. To do this, a knot is knotted at the free ends of the rope, a carabiner is attached to them. In accordance with the size of the rope, the required number of turns are made around the trunk, then the carabiner is attached.

For information on how to install a hammock on the street, see the next video.