All about Porotherm ceramic blocks

It is necessary to know everything about Porotherm ceramic blocks already because these products can give a serious advantage. We need to figure out what is good about the "warm ceramics" Porotherm 44 and Porotherm 51, porous ceramic block 38 Thermo and other block options. It is also worth familiarizing yourself with the nuances of the application, ignorance of which easily negates all the advantages.

It should be said right away that Porotherm ceramic blocks are not such a new product. Their release began in the 1970s. And since then, the basic parameters have been studied very well and comprehensively. The efficiency and high mechanical strength of such products have been confirmed in practice. The manufacturer claims that the ceramic blocks can last 50 or 60 years without major repairs.

Speaking about their main technical properties, it should be noted extremely low thermal conductivity. So, if you use a 38 cm wide structure for construction, then it will provide the same powerful thermal insulation as a traditional brick wall 235 cm thick. They are compared, of course, without taking into account additional insulation. This advantage is provided by the introduction of special substances that reduce the permeability to heat.

Other important points:

• the costs of building walls, taking into account all the necessary materials, are the same as when using gas blocks, and the quality is higher;

• there is no need for reinforcement;

• long drying is not required;

• construction time will be reduced;

• in many localities it is possible to do without additional thermal insulation;

• for the manufacture of structures, only environmentally friendly materials are used, which are carefully checked by professional engineers;

• structures are covered with a special composition that reliably resists even the most aggressive effects of the atmospheric environment;

• fire resistance is guaranteed;

• upon contact with high temperatures, the blocks can warm up for a long time, but they will not emit toxic substances;

• the optimal parameter of such an indicator as vapor permeability is provided;

• the special strength of the structures allows you to build houses up to 10 floors high without any problems.

The blocks are produced by the Austrian company Wienerberger. Part of its production facilities are located in our country. We are talking about factories in Tatarstan and in the Vladimir region. Ease of transportation to major consumers in other regions of the country can significantly reduce transportation costs. In the production process, the latest technologies are actively used, engineers are also monitoring the constant improvement of product quality.

The most recent designs have a special void shape that increases thermal efficiency. It was also possible to increase the concentration of the voids themselves - without much damage to the mechanical properties. The ceramic block allows you to achieve an optimal microclimate inside the house. If the installation is done correctly, the appearance of dampness or the appearance of cold bridges is excluded.

Modern ceramic stone also perfectly dampens extraneous sounds. Thanks to the well-thought-out properties, the thermos effect, which is typical for stone walls, is eliminated.With air humidity from 30 to 50%, maintaining the most comfortable temperature for a person is much easier than you might imagine. The ceramic block is durable because it is processed at 900 degrees. This is what guarantees the chemical and fire resistance of structures.

The Austrian company carefully complies with the standards of GOST 530 of 2012. In the manufacture of blocks, only proven and safe materials are used, such as refined clay, sawdust.

In the winter, the house will be warm, and in the hot, it will be cool. However, it should be borne in mind that Porotherm products are not so cheap. Even taking into account the reduction in construction costs, the total cost, in comparison with brick, will grow by 5% or slightly more.

It is also necessary to remember about the hygroscopicity of building ceramics. In this regard, it does not differ from brick in any way. Therefore, at all phases of construction work, first-class waterproofing will be required. The walls of the blocks are thin and fragile, so it is likely that they will be damaged during transportation. Suppliers pack these structures in a special way, but this takes up a lot of space in the bodies of cars or inside the wagons.

Masonry technology implies the ability to exclude reinforcement. Therefore, the work is easier and faster than in other situations.

In the southern regions of Russia and partly in the middle lane, special insulation is not required. A special tongue-and-groove connection allows to reduce the consumption of the building mixture (glue or cement) by at least 2 times.

One large block in size can replace up to 14 bricks. Therefore, laying the walls of a house from them is much easier and easier. The manufacturer recommends using a proprietary warm masonry mortar. It is also quite appropriate to cover Porotherm blocks with light plaster of the same brand.

Traditional cement-sand and cement-lime mortars are not suitable. They hold the blocks well, but violate their excellent thermal insulation. Better to use special mixtures. The thickness of the bed seam should be about 1.2 cm. If the wall or partition is not exposed to strong stress, it is more correct to use an intermittent bed seam. The blocks should be placed as tightly as possible to each other, and it is also necessary to provide good waterproofing in the break of the wall and basement.

The general pros and cons are important, but you need to pay attention to specific product samples. It is appropriate to start acquaintance with the porous ceramic block with the Porotherm 8 model. Its features:

• destiny - layout of interior partitions;

• adding additional space to the house (or rather, its less taking away due to the small thickness of the walls);

• great and suitable for most people tongue-and-groove installation.

In many cases, including in brick houses, it is more correct to use a Porotherm 12 block to form partitions... It is designed to accommodate 120mm baffles in one row. Compared to even the best brands of bricks, this design benefits from its large size.

But sometimes it becomes necessary to fill openings in monolithic buildings. Then the Porotherm 20 block comes to the rescue of people.... He is sometimes allowed to create interior walls and interior partitions. In total, several levels of thickened walls reach 3.6 cm. Thanks to special anchors, the load from the attached structures can be increased up to 400 and even up to 500 kg.

It can also be used to fill a monolithic frame of almost any building.The resistance to heat transfer is higher than that of any analogs offered by other manufacturers. When laying the corner, you do not need to use additional parts.

Porotherm 44 turns out to be a worthy successor to the line. This block is suitable for building houses up to 8 floors. Remarkably, additional reinforcement of the masonry is not required. There is no need to doubt the excellent microclimate and convenience for life. The wall will reliably protect both from heat leakage and from extraneous sounds.

Completing the review is quite appropriate on Porotherm 51. Such products are recommended for both private and multi-storey construction. They are suitable if you need to build a house up to 10 floors without special reinforcement. The clever tongue-and-groove connection also speeds up installation. Under normal conditions in most regions of the Russian Federation, additional insulation is not required.