Lawnmower fishing line: how to choose and reel?

With the arrival of spring, summer cottages are becoming the main residence of many of our compatriots. However, with the arrival of warm days, there is such a problem as fast-growing grass. It is inconvenient to constantly mow it with a hand scythe, and not all types of grass lend themselves to this old working tool. It is much more convenient to use modern lawn mowers for these purposes. Particularly popular among them are devices with a fishing line, which is easy to change if necessary.

Nylon lines are suitable for both electric and petrol powered trimmers. This consumable can be used for both hand tools and a wheeled lawnmower. It is important to choose the right line, as this directly affects both the result of the work and the service life of the unit. Of course, it is very easy to get confused in the offered assortment of lines, especially for beginners. However, there is a lot of advice from experts and those who have already tried various options.

For an electric trimmer less than 500 W, a thin line with a diameter of 1 to 1.6 mm is suitable. She will perfectly mow lawns with low grass. If the power of the tool is in the range from 0.5 to 1 kW, then it is better to give preference to a line with a diameter of 2 mm or slightly larger.

For petrol trimmers and brushcutters, line less than 3 mm must not be taken. This thickness will allow you to easily cope with any weeds, dry stems, dense grass. Diameter over 4 mm is only suitable for high power brushcutters. It turns out that thick line is necessary for powerful technique. It is not recommended for use with low power trimmers, otherwise it will not perform well, constantly winding around the reel and creating additional stress on the engine.

Typically, a standard package contains up to 15 meters of line. However, to replace the string on a reel, a length of about 7 meters is sufficient. It also happens that the fishing line is produced in bays of 250-500 meters. When choosing a string, it is imperative to specify the date when it was produced. Nylon that is too old can dry out and become too brittle. If this happens, then you can soak the line for a couple of hours in water, but it will not be completely the same.

When choosing, an important parameter is the section of the string, which can be of several types.

• The round section is versatile. It is used for mowing grass of medium thickness and density. It may make excessive noise during operation, but it is not used too quickly.

• A square or polygonal section is more efficient than a round one. Due to the sharp corners, the stems of plants are cut at a faster speed and better quality.

• Ribbed, twisted and star-shaped sections are the most effective. Such a fishing line manages to mow the grass very quickly. And its main disadvantage is its rapid wear.

Trimmer line is made of nylon, which is durable, lightweight, low cost and durable. To make the cost of the material even cheaper, polyethylene is added to it, but then the line overheats faster. Thick strings have a graphite or steel rod.Sometimes they are reinforced, which increases strength and service life.

In the trimmer, the element on which the string is pulled is very simple. It is called the "coil". Usually it consists of an upper and a lower part (grooves), between which there is a partition with a recess. It is on these grooves that the fishing line should be wound. However, it is first pulled through the recess.

Before removing the coil, unscrew the special button located directly on the mower body. Remove the reel from the mower before changing the line.

It is not difficult to do this, but there are some peculiarities depending on the trimmer configuration and the coil itself.

• In small e-mowers, the motor and reel are at the bottom, and buttons are located on the sides of the reel. If you press them, then you get the upper groove of the reel and the part where you need to wind the fishing line.

• In bent-arm mowers that do not have a knife, the reels have special two-horned nuts. In such tools, you must hold the bobbin so that it does not move, and at the same time turn the nut clockwise. It is she who holds the entire reel, which is then easy to remove.

• Straight arm mowers that can be fitted with a blade have a hole just below the reel. To remove the coil, a screwdriver is inserted into this hole, while the bobbin is fixed. After that, you need to turn the coil clockwise and remove it from the unit.

Sometimes there may be latches on the coil in the form of latches. They must be pressed to separate the parts of the coil. It is also possible that the top and bottom of the bobbin are connected by a thread. In this case, it is enough to grasp the top and bottom with your hands, and then twist in different directions until they unscrew.

Knowing how the reel is disassembled can speed up the line change process. It all depends on what design the coil has and how many antennae. Threading into a spool that has only one working mustache is fairly straightforward, especially if you stick to a consistent plan.

• Depending on the parameters of the reel and the length of the line set initially, it is recommended to choose a string from 2 to 5 meters.

• First, remove the bobbin from the tool and then open it.

• One end of the line must be inserted into the hole inside the bobbin.

• Next, the string should be wound onto the drum. And this is done in the opposite direction from the normal rotation of the spool. Usually, the trimmers on the inside of the bobbin have an arrow that indicates in which direction to wind.

• Part of the fishing line must be pulled out and secured in a special groove located on the inside of the reel. Its purpose is to hold the winding while bringing the bobbin into working condition.

• The end of the string must be threaded through the hole on the outside of the bobbin.

• At the last stage, you need to collect the parts of the bobbin and put them on the mower bar.

The installation of the fishing line on a reel with two mustaches occurs in a slightly different way. First, you need to determine how many grooves go along the inside of the reel, on which the line is put on. There are options with one groove, and then both mustaches must be wound together. There are also models with two grooves, when each of the mustache goes separately.

• The line must be pulled through the hole, and its mustache must be folded together and aligned.

• Then winding is performed in the opposite direction to the rotation of the bobbin on the mower. Often there is an arrow inside the spool indicating how to put the line on correctly.

• The ends of the string are fixed in special grooves or simply temporarily held by hands and pulled into the hole located on the outside of the bobbin.

• After that, the spool is closed and fastened to the rod, after which the mower is ready for work.

• The line is first folded in half to determine where the middle of the fold is.

• Further, the loop formed at the bend is threaded into the groove that is formed between the two grooves.

• After that, you can wind both rods in a separate groove.

• You can fix the mustache and assemble the coil completely in the same way as described above.

Opening a reel for the first time and winding a new line is not always easy. Over time, this procedure becomes almost automatic and will not take much time. Some reels have an automatic system that spins the line by itself. As a result, it remains only to correctly set the end of the line, and you're done. In such models, the string must be put in the hole that is on the outside of the body. Further, the bobbin is assembled, and when the winding rotates, the fishing line is put on it.

Following safety precautions will allow you to quickly and safely insert new line into the spool on the mower. It is imperative that before the replacement begins and the coil is removed, the device must be turned off, especially for electric lawn mowers. It is important to constantly remind yourself to press the special lock button. On each mower, it can be located in different places, but this is necessarily indicated in the operator's manual.

Remember to adjust the cutting element. Otherwise, the work will be unstable and of poor quality. Most often, there is a button on the unit itself that allows you to configure this. If nothing happens when you press it, or the string has loosened its tension, then you need to hold down the button and forcefully pull the line out of the reel.

Winding the line is a very demanding process. It is important to follow all the steps correctly in order to tighten the line well. Materials other than special nylon strings should not be used. It is worth remembering that you cannot put a metal wire, a rod or an iron cable instead of a fishing line. This is dangerous, as the rig can very easily cut through the shoes even of coarse material and injure the wearer. Before putting on a new line, it is important to carefully read the operating instructions for the device, since some models of lawn mowers may have their own structural features, which are important to take into account when replacing.

You can find out how to change the line on the trimmer in the video below.