How and how to seal the hole in the iron barrel?

An old metal barrel is an inhabitant of many household plots. It is regularly exposed to aggressive environmental influences - it experiences temperature extremes, rains, and sometimes snow. Perhaps it would be high time to replace it - it rusted a little, cracked somewhere, but for this you still need to find a new one. And while she's gone, it would be nice to patch up the old one. In the article, you can find out exactly how to do this.

When starting to repair a metal barrel with your own hands, it is worth:

• determine the acceptable cost of work;
• how the damage should be examined, what size it is and how critical it is;
• it is necessary to choose a method to restore the structure, taking into account what is stored in the barrel: to repair a container for drinking water, the funds must be chosen much more carefully, they should not be toxic.

It is not so difficult to seal cracks, crevices and small holes in a metal barrel at home.

Bitumen or waterproof glue such as epoxy can help repair the container. They need to cover the crack on the outside of the barrel, fix a suitable piece of rubberized fabric on them, and once again go over it with glue or bitumen.

Can be used for repairs "cold welding". She just needs to close the previously cleaned with sandpaper or a brush from rust and degreased damaged area. The main thing is to follow the instructions on the packaging of the composition. For reliability, you can apply the product from both sides. Suitable for small holes and window sealant.

A regular chopik (wooden dowel) and silicone sealant will help to fix a barrel with a small hole. Chopik is coated with sealant, driven into a hole, cut to size, and then again covered with sealant from the outside and inside. The container can be reused after 24 hours.

Instead of a chopik, you can close the hole with a suitable size bolt, nut and washer, and put rubber pads on both sides between them and the wall. If you cannot find a washer of the diameter you need, you can make one yourself from sheet metal.

The leaky bottom of the iron barrel can also be repaired without welding. Most often, two of the simplest methods of eliminating such a leak are used.

• Clay. Finding her at the dacha usually does not work. So, if a barrel leaks, which stands in one place and does not move around the site, you can do the following. At the place where you plan to keep the barrel, you need to dig a hole, and fill it 3/4 with diluted clay. A leaky barrel is installed in this pit, and a load is placed on its bottom. Everything. You don't have to do anything else. The hardened clay will solve the problem with the leaking bottom for a long time.

• Bituminous mastic plus iron sheet. A patch should be made of metal, larger in size than the hole in the bottom. After the patch is installed in place, the bottom is filled with a layer of bitumen one and a half centimeters thick. When the bitumen on the inside has frozen, it is worth covering the outside with mastic. After everything is dry, you can return the barrel to service.

The first thing to remember when starting to repair an old barrel: it is pointless to use a welding machine to eliminate the hole, regardless of its operating principle. The walls of the tank are thin, battered by time and corrosion, welding will only add new ones to the old holes.Another small subtlety: if you do not have a desire to mess with bitumen, then when repairing small gaps, it can be replaced with liquid plastic. You can find this composition in a hardware store.

You can do it cunningly - instead of repairing a rusty barrel, make it not the main container for water, but only an integral part of the structure. Here you should adhere to a certain plan of action.

1. Get the most dense and voluminous plastic bags, more than the volume of the barrel itself, scotch tape, a metal brush and aluminum wire.
2. Clean the inside of the barrel with a brush from irregularities so as not to tear the polyethylene.
3. Place one bag in another, align them and release the air that has accumulated between the bags.
4. Tape the edges of the bags together with tape. It is worth glueing every 10-15 cm of the upper edge, leaving a place for air release so that the bags do not burst.
5. Make a hook (10-15 cm) out of a wire (suitable diameter - 5 mm) and fix it on the barrel so that the upper edge of the wire extends upwards from the edge of the barrel by 5 cm. Bend the wire inside the barrel and press it against the wall.
6. Lower the bag into the barrel, bending the top edge outward by 10-15 cm along the entire perimeter of the barrel.
7. Tightly glue the bag allowance to the outside of the barrel with tape. You cannot close the outer end of the hook, it is better to glue it higher. The hook will create an additional path for air to escape.
8. Ready! The barrel can be used further.

And a few simple but important recommendations in the end:

• after most repair options, the barrel will become unsuitable for storing drinking water, remember this;
• before carrying out any manipulations, it is necessary to clean the area with which you are working from rust - the glue may simply not seize if this is not done;
• follow the instructions when working with glue, sealant or liquid plastic - this will save your nerves, money and time;
• be careful, act carefully and, perhaps, the barrel will serve you for more than one season.

For repairing an iron barrel, see the video below.