Finishing "Block House": subtleties of installation

Block house is a popular finishing material that is used to decorate the walls and facades of various buildings. It is distinguished by its attractive appearance and easy installation. This finish can be used for both exterior and interior decoration. Today we will take a closer look at the intricacies of installing such a cladding.

The block house is rightfully recognized as one of the most widespread and demanded finishing materials. Ceilings sheathed with such coatings look as if they were built from natural wood.

The block house is made of wood and galvanized steel. The latter material is additionally covered with a polymer-based film. These finishes are available in double and single finishes.

In addition to wood, metal options for such a finish are also produced - metal siding. Such coatings are made of galvanized steel, which does not corrode. These materials often imitate natural wood and look natural.

A high-quality block house is produced on machines with special cutters. Wood processing has a direct impact on the quality of the finished product.

The block house is distinguished by its shape. It has a rounded front and a flat back. On the edges of these materials, there are spikes and grooves, which are necessary for joining the lamellas on the base.

The ventilated facade, decorated with this finishing material, consists of several important components.

• In such structures, a high-quality vapor barrier must be present. This component protects the block house from steam and high humidity. The vapor barrier layer passes vapors through itself in the direction of the ceilings, preventing them from reaching the insulating canvas.
• Also, such facade systems have a crate (frame). It forms the space between the wall of the house and the block house itself. This component acts as the basis for fixing the rails. As a rule, the lathing is made of a wooden bar with a section of 100x40 mm or 50x40 mm - this parameter depends on the material of which the insulating layer consists.

• A heat-insulating layer is also required in this design. For this, inexpensive foam or mineral wool is most often used. The insulation should be at least 10 cm thick.
• Such façade systems must be equipped with a wind barrier. It is installed on the frame beam and protects the insulating layer from moisture that is present in the surrounding air.
• In the interval between the block house and the windproof film, as a rule, there is a counter lattice. It consists of small-section bars - 20x40 cm. If you do not use this element when arranging the facade, then the panels of a block house made of wood can rot rather quickly.
• The finishing layer is the facing layer from the block house.

A block house can be made of metal and wood. Let's take a closer look at what characteristics these types of finishing materials have.

To begin with, it is worth considering what is good about facing a house with wooden coverings:

• These materials have a natural and expensive design. Buildings designed in this way look cozy and welcoming.
• Wooden block house is an environmentally friendly material. There are no hazardous chemical compounds in its content. Even at high temperatures, such cladding will not emit harmful substances.
• A block house made of wood is a durable material. It is not easily damaged or broken. He is not afraid of shocks and mechanical damage.
• Quality panels are not susceptible to mold and mildew formation.

• The block house boasts excellent sound and waterproofing performance. In addition, such material will retain heat inside the house.
• Installation of wood panels is simple and affordable. Even an inexperienced home craftsman can handle it.

The main disadvantage of a wooden block house is that it must be regularly treated with antiseptic agents. If you neglect such measures, then such a material can rot, lose the brightness of color and become a haven for tree parasites.

In addition, many consumers attribute its high cost to a number of disadvantages of a wooden block house.

For interior decoration, thinner lamellas with a thickness of 20-24 mm are used. Such coatings can only be used as decorative design elements. They are great for interior decoration, as they are thin and do not take up extra free space.

The block house is made from various types of wood and is subdivided into several classes.

• "Extra". Such finishing materials are of the highest quality. They have a pleasant, smooth surface that is free of the slightest imperfections. Such a block house is expensive, as it undergoes complex processing.
• "A". Materials of this class can have small knots on their surface, slight mechanical damage, as well as darkened areas. In some places, this board may be uneven.

• "V". A block house of a class may have cracks, knots and other noticeable defects.
• "WITH". Products of this class often have serious damage, noticeable cracks and knots.

Now it's worth familiarizing yourself with the positive characteristics of a metal block house:

• this material is not subject to deformation even if it is in low and high temperatures (from -50 to +80 degrees);
• metal block house is a durable material. It can last over 50 years;
• such material is not afraid of the sun's rays and precipitation;
• metal block house is an environmentally friendly and safe material;
• it is not flammable;

• its installation is also considered quite simple;
• such a finishing material does not need to be regularly looked after using expensive means;
• a metal block house can be laid out on bases consisting of any materials, but most often this material is used to sheathe the floors of a house or a pediment;
• such panels are inexpensive, especially when compared to natural wood coatings.

The only and main drawback of the metal block house is its impressive weight. That is why such material can be purchased only if the walls of the house are sufficiently strong and reliable. There is a lightweight alternative to such a material - an aluminum block house. However, it is less durable. It can be easily wrinkled and damaged.

Choosing a block house is not an easy task. Facing boards differ from each other not only in the materials from which they are made, but also in other characteristics.

When choosing such finishing materials, it is worth relying on the recommendations of specialists.

• For facade cladding, it is worth choosing not only thicker, but also wide panels. This parameter should be at least 15 cm. Select coatings so that they have the same dimensions.
• Longer lamellas are recommended. Using such materials, you can sheathe a house with a minimum number of joints. The standard block house length is 6 m.

• Planks from the northern regions are denser and more reliable. These features have a positive effect on the other qualities of such materials. You can find out the degree of density of a tree by using the location of the annual rings. The closer they are to each other, the denser the raw material is.
• Do not buy a block house that has various defects and damage, such as rotten knots, cracks, dark spots or moldy deposits.
• Pay attention to the pitching - it should not be large. The width of such elements should not exceed 8 mm, and the depth - 3 mm.
• The permitted moisture content of the wood material is 20%. This indicator must be present in the quality certificate.
• The packaging of the block house must not be damaged. If any are present, then it is better to refuse to buy the material, since it may be damaged or prone to decay.

The block house is mounted on a frame made of wood or a metal profile. With this method of installation, constant ventilation occurs from the inside, which avoids the penetration of moisture into the material and insulation. Facade walls are constructed in two layers so that insulation can be installed between them.

The block house must be attached horizontally to the bases. In this case, the spike should be directed upwards and the groove downwards.

The tongue-and-groove locking system is optimal for such finishing options. However, in addition to this, self-tapping screws are used to attach each bar from the outside. They are installed closer to the side of the panel.

In addition to self-tapping screws, other elements are used to fasten the material:

• nails;
• kleimer;
• galvanized staples.

Blanks of material for external decoration are laid out horizontally. However, inside the building, they can also have a vertical arrangement.

It is recommended to fix the block house in the corners as follows:

• first you need to fix the bar in an upright position;
• then blanks should be attached to it.

Using this method of fastening, you will eliminate the appearance of noticeable gaps.

Before you start arranging the facade of the house, you need to calculate how much block house you will need.

Currently, similar materials are produced with various dimensional parameters:

• the width of the lamellas for finishing inside buildings is 96 mm, the length is 2-6 m, the thickness is from 20 mm;
• for outdoor decoration, a board with a width of 100 to 200 mm, a length of 4-6 m and a thickness of up to 45 cm is used.

To find out how much block house you need to buy to decorate a house, you should find out how many square meters are in the floors. To do this, the width must be multiplied by the height. Subtract the area of ​​windows and doors from the resulting value. Now you can calculate the area of ​​one panel and divide the total by the resulting value. Do not forget that in these calculations, only the working width of the material must be taken into account (without locking elements).

For example:

• the panel length is 5 m and the width is 0.1 m;
• we multiply these values ​​and as a result we get the area of ​​one panel - 0.5 sq m;
• if the total area of ​​the wall is 10 square meters, then only 20 slats will be needed to finish it;
• if there are doors and window openings on the ceiling, then it is worth buying a block house with a small margin.

You can decorate the floors with a block house with your own hands. Let's take a closer look at the step-by-step instructions for laying such a facing material.

You will need the following materials:

• special membrane for wind protection;
• roll insulation;
• vapor barrier film;
• primer;
• antiseptic composition;
• bars for the frame;
• cleats and screws for fasteners.

You also need to stock up on such tools:

• level;
• brush;
• hammer;
• Sander;
• saw;
• electric drill;
• screwdriver.

First you need to prepare the bases:

• All wooden parts should be treated with antiseptics. It is advisable to cover the boards with a fire retardant - it will protect them from fire and mold.
• A vapor barrier must be nailed to the walls of the house. The film should be fastened with an overlap of 10-15 cm. It is more convenient to do this work with a construction stapler.
• Next, you need to install the crate. It should be horizontal. The bars should be mounted using nails or self-tapping screws. If we sheathe brick or panel walls, it is better to use frame dowels.
• Insulation should be laid in open cells of the frame structure.
• Attach another layer of lathing to the main frame - vertical. To do this, the bars should be fixed with a level. It is on this basis that we will lay the block house.

• The clamps should be attached to the frame with self-tapping screws.
• The starter piece must be inserted into the mounting lugs. The position of the boards should be groove down.
• The groove of the subsequent elements must be put on the spike.
• Cladding work must be continued until the wall is completely finished.

The block house can also be installed inside the house. It can be laid out both on the walls and on the ceiling of the room. In this case, the installation of the panels will be similar to the outdoor installation.

You just need to take into account the following nuances:

• for interior decoration, a narrow cladding of small thickness is suitable;
• the outer and inner corners must be fixed only after the installation of the block house is completed.

If you have chosen a material such as a block house for interior or exterior decoration, then you you should read some recommendations from experts:

• If you plan to lay a block house on wooden floors, then first you need to thoroughly clean out the areas affected by the fungus on their surface.
• Docking materials should be especially careful and careful. In such processes, it is necessary to use a level to make sure that the docking is correct and smooth.
• The block house should not be installed on floors immediately after purchase. Repair can be started only after the panels have been lying for several days under a canopy or in a dry room.
• It is not recommended to use polystyrene for insulation, especially if you are installing not a metal, but a wooden block house.Such a heat insulator is incompatible with wood, since it supports combustion and does not have sufficient vapor permeability.

• It is recommended to use clamps during construction. Such details create a secure fit. Ordinary self-tapping screws can damage the material, and a steel clip will neatly fix the edge of the groove.
• A block house made of wood is not recommended for finishing rooms with a high level of humidity (kitchen, bathroom, toilet), otherwise the material will have to be regularly treated with protective compounds so that it does not become unusable.
• Experts recommend purchasing a high-quality block house from trusted manufacturers with a good reputation in your city. You should not look for materials for which the cube is asking for too low a price. Such coatings are most likely of the lowest grade and do not work well.

In this video you will see the block house decoration of the house.